EVAL-AD7490CB(RevA) 查看數據表（PDF） - Analog Devices

零件编号

产品描述 (功能)

生产厂家

EVAL-AD7490CB
(Rev.:RevA)

16-Channel, 1 MSPS, 12-Bit ADC with Sequencer in 28-Lead TSSOP

Analog Devices 

AD7490

supplies are applied, the Control Register will contain the correct

information and valid data will result from the next conversion.

Therefore, to ensure the part is placed into the correct operating

mode when supplies are first applied to the AD7490, the user must

first issue two serial write operations with the DIN line tied

high. On the third conversion cycle, the user can then write to the

Control Register to place the part into any of the operating modes.

The user should not write to the Shadow Register until the fourth

conversion cycle after the supplies are applied to the ADC in

order to guarantee the Control Register contains the correct data.

If the user wishes to place the part into either Normal Mode or

Full Shutdown Mode, the second dummy cycle with DIN tied

high can be omitted from the three dummy conversion operation

outlined in Figure 16.

SERIAL INTERFACE

Figure 17 shows the detailed timing diagram for serial interfacing

to the AD7490. The serial clock provides the conversion clock

and also controls the transfer of information to and from the

AD7490 during each conversion.

The CS signal initiates the data transfer and conversion process.

The falling edge of CS puts the track and hold into hold mode,

takes the bus out of three-state, and the analog input is sampled

at this point. The conversion is also initiated at this point and

will require 16 SCLK cycles to complete. The track and hold

will go back into track on the 14th SCLK falling edge as shown in

Figure 17 at point B, except when the write is to the Shadow

Register, in which case the track and hold will not return to

track until the rising edge of CS, i.e., point C in Figure 18. On

the 16th SCLK falling edge, the DOUT line will go back into

three-state (assuming the WEAK/TRI Bit is set to 0). Sixteen

serial clock cycles are required to perform the conversion process

and to access data from the AD7490. The 12 bits of data are

preceded by the four channel address bits ADD3 to ADD0,

identifying which channel the conversion result corresponds to.

CS going low provides address bit ADD3 to be read in by the

microprocessor or DSP. The remaining address bits and data bits

are then clocked out by subsequent SCLK falling edges beginning

with the second address bit ADD2; thus the first SCLK falling

edge on the serial clock has address bit ADD3 provided and also

clocks out address bit ADD2. The final bit in the data transfer is

valid on the 16th falling edge, having being clocked out on the

previous (15th) falling edge.

Writing of information to the Control Register takes place on

the first 12 falling edges of SCLK in a data transfer, assuming the

MSB, i.e., the WRITE Bit, has been set to 1. If the Control Register

is programmed to use the Shadow Register, writing of information

to the Shadow Register will take place on all 16 SCLK falling

edges in the next serial transfer (see Figure 18). The Shadow Reg-

ister will be updated upon the rising edge of CS and the track and

hold will begin to track the first channel selected in the sequence.

If the WEAK/TRI Bit in the Control Register is set to 1, rather than

returning to true three-state upon the 16th SCLK falling edge,

the DOUT line will instead be pulled weakly to the logic level

corresponding to ADD3 of the next serial transfer. This is done

to ensure that the MSB of the next serial transfer is set up in time

for the first SCLK falling edge after the CS falling edge. If the

WEAK/TRI Bit is set to 0 and the DOUT line has been in true

three-state between conversions, then depending on the particular

DSP or microcontroller interfacing to the AD7490, address bit

ADD3 may not be set up in time for the DSP/micro to clock it in

successfully. In this case, ADD3 would only be driven from the

falling edge of CS and must then be clocked in by the DSP on the

following falling edge of SCLK. However, if the WEAK/TRI Bit

had been set to 1, then although DOUT is driven with address bit

ADD3 since the last conversion, it is nevertheless so weakly driven

CS

SCLK

DOUT

DIN

t2

t6 tCONVERT

1

2

3

4

5

6

t3

THREE-

STATE ADD3

t3b

ADD2

t9

t4

ADD1

ADD0

DB11

FOUR IDENTIFICATION BITS t10

t7

DB10

WRITE

SEQ

ADD3

ADD2

ADD1

ADD0

B

13

14

15

16

t5

t11

DB2

DB1

DB0

t8

DONTC DONTC DONTC

tQUIET

THREE-

STATE

Figure 17. Serial Interface Timing Diagram

CS

SCLK

DOUT

DIN

t2

tCONVERT

t6

1

2

3

4

5

6

t3

THREE-

STATE ADD3

ADD2

t9

t4

ADD1

ADD0

DB11

FOUR IDENTIFICATION BITS t10

t7

DB10

VIN0

VIN1

VIN2

VIN3

VIN4

VIN5

C

13

14

15

16

t5

t11

DB2

DB1

DB0

t8

VIN13

VIN14

VIN15

THREE-

STATE

Figure 18. Writing to Shadow Register Timing Diagram

REV. A

–17–

Share Link: