ADV7172KST 查看數據表（PDF） - Analog Devices

零件编号

产品描述 (功能)

生产厂家

ADV7172KST

Digital PAL/NTSC Video Encoder with Six DACs (10 Bits), Color Control and Enhanced Power Management

Analog Devices 

ADV7172/ADV7173

APPENDIX 1

BOARD DESIGN AND LAYOUT CONSIDERATIONS

The ADV7172/ADV7173 is a highly integrated circuit containing

both precision analog and high speed digital circuitry. It has

been designed to minimize interference effects on the integrity

of the analog circuitry by the high speed digital circuitry. It is

imperative that these same design and layout techniques be applied

to the system level design so that high speed, accurate performance

is achieved. The Recommended Analog Circuit Layout shows

the analog interface between the device and monitor.

The layout should be optimized for lowest noise on the ADV7172/

ADV7173 power and ground lines by shielding the digital inputs

and providing good decoupling. The lead length between groups

of VAA and GND pins should by minimized to minimize induc-

tive ringing.

Ground Planes

The ground plane should encompass all ADV7172/ADV7173

ground pins, voltage reference circuitry, power supply bypass cir-

cuitry for the ADV7172/ADV7173, the analog output traces, and

all the digital signal traces leading up to the ADV7172/ADV7173.

The ground plane is the board’s common ground plane.

Power Planes

The ADV7172/ADV7173, and any associated analog circuitry,

should have its own power plane, referred to as the analog

power plane (VAA). This power plane should be connected to

the regular PCB power plane (VCC) at a single point through a

ferrite bead. This bead should be located within three inches of

the ADV7172/ADV7173.

The metallization gap separating device power plane and

board power plane should be as narrow as possible to mini-

mize the obstruction to the flow of heat from the device into

the general board.

The PCB power plane should provide power to all digital logic

on the PC board, and the analog power plane should provide

power to all ADV7172/ADV7173 power pins and voltage

reference circuitry.

Plane-to-plane noise coupling can be reduced by ensuring that

portions of the regular PCB power and ground planes do not

overlay portions of the analog power plane unless they can be

arranged so that the plane-to-plane noise is common-mode.

Supply Decoupling

For optimum performance, bypass capacitors should be in-

stalled using the shortest leads possible, consistent with reliable

operation, to reduce the lead inductance. Best performance is

obtained with 0.1 µF ceramic capacitor decoupling. Each group

of VAA pins on the ADV7172/ADV7173 must have at least one

0.1 µF decoupling capacitor to GND. These capacitors should

be placed as close to the device as possible.

It is important to note that while the ADV7172/ADV7173

contains circuitry to reject power supply noise, this rejection

decreases with frequency. If a high frequency switching power

supply is used, the designer should pay close attention to reduc-

ing power supply noise and consider using a three-terminal voltage

regulator for supplying power to the analog power plane.

Digital Signal Interconnect

The digital inputs to the ADV7172/ADV7173 should be iso-

lated as much as possible from the analog outputs and other

analog circuitry. Also, these input signals should not overlay the

analog power plane.

Due to the high clock rates involved, long clock lines to the

ADV7172/ADV7173 should be avoided to reduce noise pickup.

Any active termination resistors for the digital inputs should be

connected to the regular PCB power plane (VCC) and not the

analog power plane.

Analog Signal Interconnect

The ADV7172/ADV7173 should be located as close to the

output connectors as possible to minimize noise pickup and

reflections due to impedance mismatch.

The video output signals should overlay the ground plane, not

the analog power plane, to maximize the high frequency power

supply rejection.

Digital inputs, especially pixel data inputs and clocking signals,

should never overlay any of the analog signal circuitry and

should be kept as far away as possible.

For best performance, the outputs should each have a 75 Ω load

resistor connected to GND. These resistors should be placed

as close as possible to the ADV7172/ADV7173 to minimize

reflections.

The ADV7172/ADV7173 should have no inputs left floating.

Any inputs that are not required should be tied to ground.

REV. B

–41–

Share Link: