AT49HF010-12JI 查看數據表（PDF） - Atmel Corporation
零件编号
产品描述 (功能)
生产厂家
AT49HF010-12JI Datasheet PDF : 10 Pages
| |||
AT49F010/HF010
PRODUCT IDENTIFICATION: The product identification
mode identifies the device and manufacturer as Atmel. It
may be accessed by hardware or software operation. The
hardware operation mode can be used by an external pro-
grammer to identify the correct programming algorithm for
the Atmel product.
For details, see Operating Modes (for hardware operation)
or Software Product Identification. The manufacturer and
device code is the same for both modes.
DATA POLLING: The AT49F010/HF010 features DATA
polling to indicate the end of a program cycle. During a
program cycle an attempted read of the last byte loaded
will result in the complement of the loaded data on I/O7.
Once the program cycle has been completed, true data is
valid on all outputs and the next cycle may begin. DATA
polling may begin at any time during the program cycle.
T O G G L E B I T : I n a d d i t i o n t o DATA p o l l i n g t h e
AT49F010/HF010 provides another method for determin-
ing the end of a program or erase cycle. During a program
or erase operation, successive attempts to read data from
the device will result in I/O6 toggling between one and
zero. Once the program cycle has completed, I/O6 will
stop toggling and valid data will be read. Examining the
toggle bit may begin at any time during a program cycle.
HARDWARE DATA PROTECTION: Hardware features
protect against inadvertent programs to the
AT49F010/HF010 in the following ways: (a) VCC sense: if
VCC is below 3.8V (typical), the program function is inhib-
ited. (b) Program inhibit: holding any one of OE low, CE
high or WE high inhibits program cycles. (c) Noise filter:
Pulses of less than 15 ns (typical) on the WE or CE inputs
will not initiate a program cycle.
Command Definition (in Hex)
Command Bus
Sequence Cycles
1st Bus
Cycle
Addr Data
Read
1
Addr DOUT
Chip Erase 6
5555 AA
Byte
Program
4
5555 AA
Boot Block
Lockout (1)
6
5555 AA
Product ID
Entry
3
5555 AA
Product ID
Exit (2)
3
5555 AA
Product ID
Exit (2)
1
XXXX F0
2nd Bus
Cycle
Addr Data
2AAA 55
2AAA 55
2AAA 55
2AAA 55
2AAA 55
3rd Bus
Cycle
Addr Data
5555 80
5555 A0
5555 80
5555 90
5555 F0
4th Bus
Cycle
Addr Data
5555 AA
Addr DIN
5555 AA
Notes: 1. The 8K byte boot sector has the address range 00000H to 01FFFH.
2. Either one of the Product ID exit commands can be used.
Absolute Maximum Ratings*
5th Bus
Cycle
Addr Data
2AAA 55
2AAA 55
6th Bus
Cycle
Addr Data
5555 10
5555 40
Temperature Under Bias................. -55°C to +125°C
Storage Temperature...................... -65°C to +150°C
All Input Voltages
(including NC Pins)
with Respect to Ground ................... -0.6V to +6.25V
All Output Voltages
with Respect to Ground .............-0.6V to VCC + 0.6V
Voltage on OE
with Respect to Ground ................... -0.6V to +13.5V
*NOTICE: Stresses beyond those listed under “Absolute Maxi-
mum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the
device at these or any other conditions beyond those indi-
cated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
3
Share Link: 