MAX17006AETP 查看數據表（PDF） - Maxim Integrated

零件编号

产品描述 (功能)

生产厂家

MAX17006AETP

1.2MHz, Low-Cost, High-Performance Chargers

Maxim Integrated 

1.2MHz, Low-Cost,

High-Performance Chargers

CC, CCI, CCS, and LVC Control Blocks

The MAX17005A/MAX17006A/MAX17015A control

input current (CCS control loop), charge current (CCI

control loop), or charge voltage (CC control loop),

depending on the operating condition. The three con-

trol loops, CC, CCI, and CCS are brought together

internally at the lowest voltage clamp (LVC) amplifier.

The output of the LVC amplifier is the feedback control

signal for the DC-DC controller. The minimum voltage

at the CC, CCI, or CCS appears at the output of the

LVC amplifier and clamps the other control loops to

within 0.3V above the control point. Clamping the other

two control loops close to the lowest control loop

ensures fast transition with minimal overshoot when

switching between different control loops (see the

Compensation section). The CCS and CCI loops are

compensated internally, and the CC loop is compen-

sated externally.

Continuous-Conduction Mode

With sufficiently large charge current, the MAX17005A/

MAX17006A/MAX17015s’ inductor current never cross-

es zero, which is defined as continuous-conduction

mode. The controller starts a new cycle by turning on

the high-side MOSFET and turning off the low-side

MOSFET. When the charge-current feedback signal

(CSI) is greater than the control point (LVC), the CCMP

comparator output goes high and the controller initiates

the off-time by turning off the high-side MOSFET and

turning on the low-side MOSFET. The operating fre-

quency is governed by the off-time and is dependent

upon VCSIN and VDCIN.

The on-time can be determined using the following

equation:

tON

=

L × IRIPPLE

VDCIN - VBATT

where:

IRIPPLE

=

VBATT ×

L

tOFF

The switching frequency can then be calculated:

fSW

=

tON

1

+ tOFF

At the end of the computed off-time, the controller initi-

ates a new cycle if the control point (LVC) is greater

than 10mV (VCSIP - VCSIN referred), and the charge

current is less than the cycle-by-cycle current limit.

Restated another way, IMIN must be high, IMAX must

be low, and OVP must be low for the controller to initi-

ate a new cycle. If the peak inductor current exceeds

IMAX comparator threshold or the output voltage

exceeds the OVP threshold, then the on-time is termi-

nated. The cycle-by-cycle current limit effectively pro-

tects against overcurrent and short-circuit faults.

If during the off-time the inductor current goes to zero,

the ZCMP comparator output pulls high, turning off the

low-side MOSFET. Both the high- and low-side

MOSFETs are turned off until another cycle is ready to

begin. ZCOMP causes the MAX17005A/MAX17006A/

MAX17015A to enter into the discontinuous conduction

mode (see the Discontinuous Conduction section).

Discontinuous Conduction

The MAX17005A/MAX17006A/MAX17015A can also

operate in discontinuous conduction mode to ensure that

the inductor current is always positive. The MAX17005A/

MAX17006A/MAX17015A enter discontinuous conduction

mode when the output of the LVC control point falls below

10mV (referred at VCSIP - VCSIN). For RS2 = 10mΩ, this

corresponds to a peak inductor current of 1A.

In discontinuous mode, a new cycle is not started until

the LVC voltage rises above IMIN. Discontinuous mode

operation can occur during conditioning charge of

overdischarged battery packs, when the charge cur-

rent has been reduced sufficiently by the CCS control

loop, or when the charger is in constant-voltage mode

with a nearly full battery pack.

Compensation

The charge voltage, charge current, and input current-

limit regulation loops are compensated separately. The

charge current and input current-limit loops, CCI and

CCS, are compensated internally, whereas the charge

voltage loop is compensated externally at CC.

16 ______________________________________________________________________________________

Share Link: