MMA1213D 查看數據表（PDF） - Motorola => Freescale
零件编号
产品描述 (功能)
生产厂家
MMA1213D Datasheet PDF : 8 Pages
| |||
Freescale Semiconductor, Inc.
Operating Characteristics
(Unless otherwise noted: –40°C ≤ TA ≤ +105°C, 4.75 ≤ VDD ≤ 5.25, Acceleration = 0g, Loaded output.(1))
Characteristic
Operating Range (2)
Supply Voltage (3)
Supply Current
Operating Temperature Range
Acceleration Range
Output Signal
Zero g (TA = 25°C, VDD = 5.0 V)(4)
Zero g
Sensitivity (TA = 25°C, VDD = 5.0 V)(5)
Sensitivity
Bandwidth Response
Nonlinearity
Noise
RMS (0.1-1 kHz)
Power Spectral Density
Clock Noise (without RC load on output)(6)
Self-Test
Output Response
Input Low
Input High
Input Loading(7)
Response Time(8)
Status(12)(13)
Output Low (Iload = 100 µA)
Output High (Iload = 100 µA)
Minimum Supply Voltage (LVD Trip)
Clock Monitor Fail Detection Frequency
Output Stage Performance
Electrical Saturation Recovery Time(9)
Full Scale Output Range (IOUT = 200 µA)
Capacitive Load Drive(10)
Output Impedence
Mechanical Characteristics
Transverse Sensitivity(11)
Package Resonance
Symbol
VDD
IDD
TA
gFS
VOFF
VOFF,V
S
SV
f–3dB
NLOUT
nRMS
nPSD
nCLK
gST
VIL
VIH
IIN
tST
VOL
VOH
VLVD
fmin
tDELAY
VFSO
CL
ZO
VXZ,YZ
fPKG
Min
Typ
Max
Unit
4.75
5.00
5.25
V
3.0
—
6.0
mA
–40
—
+125
°C
—
56.3
—
g
2.35
0.46 VDD
38
7.44
360
–1.0
2.5
0.50 VDD
40
8
400
—
2.65
0.54 VDD
42
8.56
440
1.0
V
V
mV/g
mV/g/V
Hz
% FSO
—
—
2.8
mVrms
—
110
—
µV/(Hz1/2)
—
2.0
—
mVpk
24
30
36
g
VSS
—
0.3 × VDD
V
0.7 × VDD
—
VDD
V
–30
–100
–260
µA
—
2.0
10
ms
—
—
0.4
—
VDD –.8
—
—
—
2.7
3.25
4.0
V
50
—
260
kHz
—
–0.25
—
—
0.2
—
ms
—
VDD –0.25
V
—
100
pF
300
—
Ω
—
—
5.0
% FSO
—
10
—
kHz
NOTES:
1. For a loaded output the measurements are observed after an RC filter consisting of a 1 kΩ resistor and a 0.01 µF capacitor to ground.
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 4.75 and 5.25 volts, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the
device may operate as a linear device but is not guaranteed to be in calibration.
4. The device can measure both + and – acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
will increase above VDD/2 and for negative acceleration the output will decrease below VDD/2.
5. The device is calibrated at 20g.
6. At clock frequency ≅70 kHz.
7. The digital input pin has an internal pull-down current source to prevent inadvertent self test initiation due to external board level leakages.
8. Time for the output to reach 90% of its final value after a self-test is initiated.
9. Time for amplifiers to recover after an acceleration signal causing them to saturate.
10. Preserves phase margin (60°) to guarantee output amplifier stability.
11. A measure of the device's ability to reject an acceleration applied 90° from the true axis of sensitivity.
12. The Status pin output is not valid following power-up until at least one rising edge has been applied to the self-test pin. The Status pin is high
whenever the self-test input is high, as a means to check the connectivity of the self-test and Status pins in the application.
13. The Status pin output latches high if a Low Voltage Detection or Clock Frequency failure occurs, or the EPROM parity changes to odd. The
Status pin can be reset low if the self-test pin is pulsed with a high input for at least 100 µs, unless a fault condition continues to exist.
Motorola Sensor Device Data
For More Information On This Product,
Go to: www.freescale.com
MMA1213D
3
Share Link: 