PCF8566 查看數據表（PDF） - Philips Electronics

零件编号

产品描述 (功能)

生产厂家

PCF8566

Universal LCD driver for low multiplex rates

Philips Electronics 

Philips Semiconductors

Universal LCD driver for low multiplex

rates

Product specification

PCF8566

7.5 PCF8566 I2C-bus controller

The PCF8566 acts as an I2C-bus slave receiver. It does

not initiate I2C-bus transfers or transmit data to an I2C-bus

master receiver. The only data output from the PCF8566

are the acknowledge signals of the selected devices.

Device selection depends on the I2C-bus slave address,

on the transferred command data and on the hardware

subaddress.

In single device applications, the hardware subaddress

inputs A0, A1 and A2 are normally left open-circuit or tied

to VSS which defines the hardware subaddress 0.

In multiple device applications A0, A1 and A2 are left

open-circuit or tied to VSS or VDD according to a binary

coding scheme such that no two devices with a common

I2C-bus slave address have the same hardware

subaddress.

In the power-saving mode it is possible that the PCF8566

is not able to keep up with the highest transmission rates

when large amounts of display data are transmitted. If this

situation occurs, the PCF8566 forces the SCL line LOW

until its internal operations are completed. This is known

as the ‘clock synchronization feature’ of the I2C-bus and

serves to slow down fast transmitters. Data loss does not

occur.

7.6 Input filters

To enhance noise immunity in electrically adverse

environments, RC low-pass filters are provided on the

SDA and SCL lines.

7.7 I2C-bus protocol

Two I2C-bus slave addresses (0111110 and 0111111) are

reserved for PCF8566. The least-significant bit of the slave

address that a PCF8566 will respond to is defined by the

level tied at its input SA0 (pin 10). Therefore, two types of

PCF8566 can be distinguished on the same I2C-bus which

allows:

1. Up to 16 PCF8566s on the same I2C-bus for very large

LCD applications

2. The use of two types of LCD multiplex on the same

I2C-bus.

The I2C-bus protocol is shown in Fig.15. The sequence is

initiated with a START condition (S) from the I2C-bus

master which is followed by one of the two PCF8566 slave

addresses available. All PCF8566s with the corresponding

SA0 level acknowledge in parallel the slave address but all

PCF8566s with the alternative SA0 level ignore the whole

I2C-bus transfer. After acknowledgement, one or more

command bytes (m) follow which define the status of the

addressed PCF8566s. The last command byte is tagged

with a cleared most-significant bit, the continuation bit C.

The command bytes are also acknowledged by all

addressed PCF8566s on the bus.

After the last command byte, a series of display data bytes

(n) may follow. These display data bytes are stored in the

display RAM at the address specified by the data pointer

and the subaddress counter. Both data pointer and

subaddress counter are automatically updated and the

data are directed to the intended PCF8566 device.

The acknowledgement after each byte is made only by the

(A0, A1, A2) addressed PCF8566. After the last display

byte, the I2C-bus master issues a STOP condition (P).

7.8 Command decoder

The command decoder identifies command bytes that

arrive on the I2C-bus. All available commands carry a

continuation bit C in their most-significant bit position

(see Fig.16). When this bit is set, it indicates that the next

byte of the transfer to arrive will also represent a

command.

If the bit is reset, it indicates the last command byte of the

transfer. Further bytes will be regarded as display data.

The five commands available to the PCF8566 are defined

in Table 5.

1998 May 04

19

Share Link: