PIC16LC72A-04I/SO 查看數據表（PDF） - Microchip Technology

零件编号

产品描述 (功能)

生产厂家

PIC16LC72A-04I/SO

28-Pin 8-Bit CMOS Microcontrollers

Microchip Technology 

3.2 PORTB and the TRISB Register

PORTB is an 8-bit wide bi-directional port. The corre-

sponding data direction register is TRISB. Setting a

TRISB bit (=1) will make the corresponding PORTB pin

an input, (i.e., put the corresponding output driver in a

hi-impedance mode). Clearing a TRISB bit (=0) will

make the corresponding PORTB pin an output, (i.e.,

put the contents of the output latch on the selected pin).

Each of the PORTB pins has a weak internal pull-up. A

single control bit can turn on all the pull-ups. This is per-

formed by clearing bit RBPU (OPTION_REG<7>). The

weak pull-up is automatically turned off when the port

pin is configured as an output. The pull-ups are dis-

abled on a Power-on Reset.

FIGURE 3-3:

RBPU(2)

Data Bus

WR Port

WR TRIS

BLOCK DIAGRAM OF

RB3:RB0 PINS

VDD

Data Latch

DQ

P

weak

pull-up

CK

TRIS Latch

DQ

CK

TTL

Input

Buffer

I/O

pin(1)

RD TRIS

RD Port

QD

EN

RB0/INT

Schmitt Trigger

Buffer

RD Port

Note 1: I/O pins have diode protection to VDD and VSS.

2: To enable weak pull-ups, set the appropriate TRIS bit(s)

and clear the RBPU bit (OPTION_REG<7>).

PIC16C62B/72A

Four of PORTB’s pins, RB7:RB4, have an interrupt on

change feature. Only pins configured as inputs can

cause this interrupt to occur (i.e. any RB7:RB4 pin con-

figured as an output is excluded from the interrupt on

change comparison). The input pins (of RB7:RB4) are

compared with the old value latched on the last read of

PORTB. The “mismatch” outputs of RB7:RB4 are

OR’ed together to generate the RB Port Change Inter-

rupt with flag bit RBIF (INTCON<0>).

This interrupt can wake the device from SLEEP. The

user, in the interrupt service routine, can clear the inter-

rupt in the following manner:

a) Any read or write of PORTB. This will end the

mismatch condition.

b) Clear flag bit RBIF.

A mismatch condition will continue to set flag bit RBIF.

Reading PORTB will end the mismatch condition and

allow flag bit RBIF to be cleared.

The interrupt on change feature is recommended for

wake-up on key depression operation and operations

where PORTB is only used for the interrupt on change

feature. Polling of PORTB is not recommended while

using the interrupt on change feature.

RB0/INT is an external interupt pin and is configured

using the INTEDG bit (OPTION_REG<6>). RB0/INT is

discussed in detail in Section 10.10.1.

FIGURE 3-4:

RBPU(2)

Data Bus

WR Port

BLOCK DIAGRAM OF

RB7:RB4 PINS

VDD

Data Latch

DQ

CK

P

weak

pull-up

I/O

pin(1)

TRIS Latch

DQ

WR TRIS

CK

TTL

Input

Buffer

ST

Buffer

RD TRIS

Latch

QD

Set RBIF

RD Port

EN

Q1

From other

RB7:RB4 pins

QD

EN

RB7:RB6 in serial programming mode

RD Port

Q3

Note 1: I/O pins have diode protection to VDD and VSS.

2: To enable weak pull-ups, set the appropriate TRIS bit(s)

and clear the RBPU bit (OPTION_REG<7>).

© 1999 Microchip Technology Inc.

Preliminary

DS35008B-page 21

Share Link: