LTC1198-1(Rev_0) 查看數據表（PDF） - Linear Technology

零件编号

产品描述 (功能)

生产厂家

LTC1198-1
(Rev.:Rev_0)

8-Bit, SO-8, 1MSPS ADCs with Auto-Shutdown Options

Linear Technology 

LTC1196/LTC1198

APPLICATI S I FOR ATIO

Offset with Reduced VREF

The offset of the LTC1196 has a larger effect on the output

code when the ADC is operated with reduced reference

voltage. The offset (which is typically a fixed voltage)

becomes a larger fraction of an LSB as the size of the LSB

is reduced. The typical curve of Unadjusted Offset Error vs

Reference Voltage shows how offset in LSBs is related to

reference voltage for a typical value of VOS. For example,

a VOS of 2mV which is 0.1LSB with a 5V reference

becomes 0.5LSB with a 1V reference and 2.5LSB with a

0.2V reference. If this offset is unacceptable, it can be

corrected digitally by the receiving system or by offsetting

the “–” input of the LTC1196.

Noise with Reduced VREF

The total input referred noise of the LTC1196 can be

reduced to approximately 2mVP-P using a ground plane,

good bypassing, good layout techniques and minimizing

noise on the reference inputs. This noise is insignificant

with a 5V reference but will become a larger fraction of an

LSB as the size of the LSB is reduced.

For operation with a 5V reference, the 2mV noise is only

0.1LSB peak-to-peak. In this case, the LTC1196 noise

will contribute virtually no uncertainty to the output

code. However, for reduced references, the noise may

become a significant fraction of an LSB and cause

undesirable jitter in the output code. For example, with

a 1V reference, this same 2mV noise is 0.5LSB peak-to-

peak. This will reduce the range of input voltages over

which a stable output code can be achieved by 1LSB. If

the reference is further reduced to 200mV, the 2mV

noise becomes equal to 2.5LSB and a stable code is

difficult to achieve. In this case averaging readings is

necessary.

This noise data was taken in a very clean setup. Any setup

induced noise (noise or ripple on VCC, VREF or VIN) will add

to the internal noise. The lower the reference voltage to be

used, the more critical it becomes to have a clean, noise-

free setup.

DYNAMIC PERFORMANCE

The LTC1196/LTC1198 have exceptionally high speed

sampling capability. Fast Fourier Transform (FFT) test

techniques are used to characterize the ADC’s frequency

response, distortion and noise at the rated throughput. By

applying a low distortion sine wave and analyzing the

digital output using a FFT algorithm, the ADC’s spectral

content can be examined for frequencies outside the

fundamental. Figure 10 shows a typical LTC1196 FFT plot.

0

–10

–20

–30

–40

–50

–60

–70

–80

–90

–100

0

VCC = 5V

fIN = 29kHz

fSMPL = 882kHz

100 200 300 400 500

FREQUENCY (kHz)

1196/98 G25

Figure 10. LTC1196 Non-Averaged, 4096 Point FFT Plot

Signal-to-Noise Ratio

The Signal-to-Noise plus Distortion Ratio [S/(N + D)] is

the ratio between the RMS amplitude of the fundamental

input frequency to the RMS amplitude of all other fre-

quency components at the ADC’s output. The output is

band limited to frequencies above DC and below one half

the sampling frequency. Figure 10 shows a typical spec-

tral content with a 882kHz sampling rate.

Effective Number of Bits

The Effective Number of Bits (ENOBs) is a measurement of

the resolution of an ADC and is directly related to S/(N + D)

by the equation:

N = [S/(N + D) –1.76]/6.02

where N is the effective number of bits of resolution and

S/(N + D) is expressed in dB. At the maximum sampling

21

Share Link: