TLP700 查看數據表（PDF） - Toshiba
零件编号
产品描述 (功能)
生产厂家
TLP700 Datasheet PDF : 17 Pages
| |||
Absolute Maximum Ratings (Ta = 25 °C)
TLP700
Characteristics
Symbol
Rating
Unit
Forward current
Forward current derating (Ta ≥ 85°C)
Peak transient forward current
(Note 1)
Reverse voltage
Junction temperature
“H” peak output current
Ta=-40 to 100 °C
“L” peak output current
(Note 2)
Output voltage
Supply voltage
Junction temperature
Operating frequency
(Note 3)
Operating temperature range
Storage temperature range
Lead soldering temperature (10 s)
(Note 4)
Isolation voltage (AC, 1 minute, R.H. ≤ 60%) (Note 5)
IF
ΔIF/ΔTa
IFP
VR
Tj
IOPH
IOPL
VO
VCC
Tj
f
Topr
Tstg
Tsol
BVS
20
−0.54
1
5
125
−2.0
2.0
35
35
125
50
−40 to 100
−55 to 125
260
5000
mA
mA/°C
A
V
°C
A
A
V
V
°C
kHz
°C
°C
°C
Vr m s
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1:
Note 2:
Note 3:
Note 4:
Pulse width PW ≤ 1 μs, 300 pps
Exponential waveform pulse width PW ≤ 0.3 μs, f ≤15 kHz
Exponential waveform IOPH ≥−1.5 A (≤ 0.3 μs), IOPL ≤+1.5 A (≤ 0.3 μs), Ta=100°C
For the effective lead soldering area
Note 5: Device considered a two-terminal device: pins 1, 2 and 3 paired with pins 4, 5 and 6 respectively.
Note 6: A ceramic capacitor (0.1 μF) should be connected from pin 6 to pin 4 to stabilize the operation of the high
gain linear amplifier. Failure to provide the bypassing may impair the switching property.
The total lead length between capacitor and coupler should not exceed 1 cm.
Recommended Operating Conditions
Characteristics
Symbol
Min Typ. Max Unit
Input current, ON
(Note 7)
IF (ON)
7.5
⎯
10
mA
Input voltage, OFF
VF (OFF)
0
⎯
0.8
V
Supply voltage *
(Note 8)
VCC
15
⎯
30
V
Peak output current
IOPH / IOPL
⎯
⎯ ± 1.5 A
Operating temperature
Topr
−40
⎯
100
°C
* This item denotes operating ranges, not meaning of recommended operating conditions.
Note : Recommended operating conditions are given as a design guideline to obtain expected performance of the
device. Additionally, each item is an independent guideline respectively. In developing designs using this
product, please confirm specified characteristics shown in this document.
Note 7: Input signal rise time (fall time) ≤ 0.5 μs.
Note 8: If the Vcc rise slope is sharp, an internal circuit might not operate with stability. Please design the Vcc rise
slope under 3.0 V/μs.
2
2010-02-23
Share Link: 