NC7WB3306(2003) 查看數據表（PDF） - Fairchild Semiconductor
零件编号
产品描述 (功能)
生产厂家
NC7WB3306 Datasheet PDF : 9 Pages
| |||
Absolute Maximum Ratings(Note 1)
Supply Voltage (VCC)
DC Switch Voltage (VS)
−0.5V to +7.0V
−0.5V to +7.0V
DC Output Voltage (VIN) (Note 2)
DC Input Diode Current
−0.5V to +7.0V
(IIK) VIN < 0V
−50 mA
DC Output (IOUT) Current
128 mA
DC VCC or Ground Current (ICC/GND)
±100 mA
Storage Temperature Range (TSTG)
−65°C to +150°C
Junction Lead Temperature under Bias (TJ)
+150°C
Lead Temperature (TL)
(Soldering, 10 seconds)
+260°C
Power Dissipation (PD) @ +85°C
250 mW
Recommended Operating
Conditions (Note 3)
Supply Operating (VCC)
Control Input Voltage (VIN)
Switch Input Voltage (VIN)
Output Voltage (VOUT)
Operating Temperature (TA)
Input Rise and Fall Time (tr, tf)
Control Input
Switch I/O
Thermal Resistance (θJA)
4.0V to 5.5V
0V to 5.5V
0V to 5.5V
0V to 5.5V
−40°C to +85°C
0 ns/V to 5 ns/V
0 ns/V to DC
250°C/W
Note 1: The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum ratings.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
Note 2: The input and output negative voltage ratings may be exceeded if
the input and output diode current ratings are observed.
Note 3: Unused logic inputs must be held HIGH or LOW. They may not
float.
DC Electrical Characteristics
Symbol
Parameter
VCC
TA = −40°C to +85°C
Units
(V)
Min
Typ
Max
Conditions
VIK
Clamp Diode Voltage
VIH
HIGH Level Input Voltage
VIL
LOW Level Input Voltage
VOH
HIGH Level Output Voltage
IIN
Input Leakage Current
IOFF
Switch OFF Leakage Current
RON
Switch On Resistance
(Note 4)
ICC
∆ICC
Quiescent Supply Current
Increase in ICC per Input
(Note 5)
4.5
−1.2
4.0 to 5.5 2.0
4.0 to 5.5
0.8
4.5 to 5.5
see Figure 3
5.5
±1.0
5.5
±1.0
4.5
3
7
4.5
3
7
4.5
6
15
4.0
10
20
5.5
3
5.5
1
2.5
V
IIN = −18 mA
V
V
V
VIN = VCC
µA 0 ≤ VIN ≤ 5.5V
µA 0 ≤ A, B, ≤ VCC
VIN = 0V, IIN = 64 mA
Ω
VIN = 0V, IIN = 30 mA
VIN = 2.4V, IIN = 15 mA
VIN = 2.4V, IIN = 15 mA
µA VIN = VCC or GND,
IOUT = 0
mA VIN = 3.4V, IO = 0,
Control Input Only
Note 4: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the
voltages on the two (A or B) pins.
Note 5: Per TTL driven input (VIN = 3.4V, control input only). A and B pins do not contribute to ICC.
3
www.fairchildsemi.com
Share Link: 