LANSDALE Semiconductor, Inc.
ML145583
MAXIMUM RATINGS (Voltage polarities referenced to GND)
Rating
Symbol
Value
Unit
DC Supply Voltage
Input Voltage
Rx1 – Rx5 Inputs
DI1 – DI3 Inputs
DC Current per Pin
VCC
VIR
I
– 0.5 to + 6.0
V
VSS – 15 to VDD + 15
V
– 0.5 to VCC + 0.5
± 100
mA
Power Dissipation
Operating Temperature Range
Storage Temperature Range
PD
1
W
TA
– 40 to + 85
°C
Tstg
– 85 to + 150
°C
RECOMMENDED OPERATING LIMITS
Parameter
Power Supply
Operating Temperature Range
* Capacitors C1 and C2 are replaced by a 1 µF capacitor at VCC = 5 V.
Symbol
VCC
VCC*
TA
This device contains protection circuitry to
guard against damage due to high static
voltages or electric fields. However, precau-
tions must be taken to avoid applications of
any voltage higher than maximum rated volt-
ages to this high–impedance circuit. For proper
operation, it is recommended that the voltage
at the DI and DO pins be constrained to the
range GND ≤ VDI ≤ VCC and GND ≤ VDO
≤ VCC. Also, the voltage at the Rx pin should
be constrained to (VSS – 15 V) ≤ VRx1 – Rx5
≤ (VDD + 15 V), and Tx should be constrained
to VSS ≤ VTx1 – Tx3 ≤ VDD.
Unused inputs must always be tied to an
appropriate logic voltage level (e.g., GND or
VCC for DI, and GND for Rx).
Min
Typ
Max
Unit
3.0
3.3
3.6
V
4.5
5.0
5.5
– 40
—
85
°C
DC ELECTRICAL CHARACTERISTICS (Voltage polarities referenced to GND = 0 V; C1 – C5 = 1 µF; TA = 25°C)
Parameter
Symbol
Min
Typ
Max
Unit
DC Power Supply
VCC
3.0
3.3
3.6
V
Quiescent Supply Current (Output Unloaded, Input Low)
ICC
—
2.8
6.0
mA
Quiescent Supply Current (Standby Mode; STB = 1, Output Unloaded)
ICC(STB)
—
<5
10
µA
Control Signal Input Voltage (STB)
VIL
—
—
VIH
VCC – 0.5
—
0.5
V
—
Control Signal Input Current (STB)
IIL
—
—
10
µA
IIH
—
—
10
Charge Pumps Output Voltage (VCC = 3 V; C1, C2, C3, C4, C5 = 1 µF)
VDD
Output Voltage (VDD)
Iload = 0 mA
8.5
8.8
Iload = 6 mA
7.5
7.9
V
—
—
Output Voltage (VSS)
Iload = 0 mA
VSS
—
– 8.8
– 8.5
Iload = 6 mA
—
– 7.8
– 7.0
RECEIVER ELECTRICAL SPECIFICATIONS
(Voltage polarities referenced to GND = 0 V; VCC = + 3.3 V 10%; C1 – C5 = 1 µF; TA = 25°C)
Parameter
Symbol
Min
Typ
Input Turn–On Threshold (VDO1 – DO5 = VOL; Rx1 – Rx5)
3.3 V
Von
1.35
1.8
5.0 V
2.00
2.5
Input Turn–Off Threshold (VDO1 – DO5 = VOH; Rx1 – Rx5)
3.3 V
Voff
0.75
1.0
5.0 V
1.20
1.5
Input Resistance
High–Level Output Voltage (DO1 – DO5)
VRx1 – Rx5 = – 3 to – 25 V
Low–Level Output Voltage (DO1 – DO5)
VRx1 – Rx5 = + 3 to + 25 V
Ring Monitor Circuit (Input Threshold)
High–Level Output Voltage (RIMON)
Low–Level Output Voltage (RIMON)
Rin
3
5.4
Iout = – 20 µA
VOH
VCC – 0.1
—
Iout = – 1 mA
VCC – 0.6
2.7
Iout = + 20 µA
VOL
—
0.01
Iout = + 1.6 mA
—
0.5
VTH
—
1.1
Iout = – 20 µA
VOH
VCC – 0.1
—
Iout = – 1 mA
VCC – 0.6
2.7
Iout = + 20 µA
VOL
—
0.01
Iout = + 1.6 mA
—
0.5
Max
Unit
2.35
V
3.10
1.25
V
1.80
7
kΩ
—
V
—
0.1
V
0.7
—
V
—
V
—
0.1
V
0.7
Page 3 of 7
www.lansdale.com
Issue A