LPC1342FHN33 查看數據表（PDF） - NXP Semiconductors.

零件编号

产品描述 (功能)

生产厂家

LPC1342FHN33

32-bit ARM Cortex-M3 microcontroller; up to 32 kB flash and 8 kB SRAM; USB device

NXP Semiconductors. 

NXP Semiconductors

LPC1311/13/42/43

32-bit ARM Cortex-M3 microcontroller

Table 4. LPC1311/13/42/43 HVQFN33 pin description table …continued

Symbol

Pin Start Type Reset Description

logic

state

input

[1]

PIO1_7/TXD/

CT32B0_MAT1

32[3] yes I/O I; PU PIO1_7 — General purpose digital input/output pin.

O-

TXD — Transmitter output for UART.

O-

CT32B0_MAT1 — Match output 1 for 32-bit timer 0.

PIO1_8/

CT16B1_CAP0

7[3] yes I/O I; PU PIO1_8 — General purpose digital input/output pin.

I

-

CT16B1_CAP0 — Capture input 0 for 16-bit timer 1.

PIO1_9/

CT16B1_MAT0

12[3] yes I/O I; PU PIO1_9 — General purpose digital input/output pin.

O-

CT16B1_MAT0 — Match output 0 for 16-bit timer 1.

PIO1_10/AD6/

CT16B1_MAT1

20[5] yes I/O I; PU PIO1_10 — General purpose digital input/output pin.

I

-

AD6 — A/D converter, input 6.

O-

CT16B1_MAT1 — Match output 1 for 16-bit timer 1.

PIO1_11/AD7

27[5] yes I/O I; PU PIO1_11 — General purpose digital input/output pin.

I

-

AD7 — A/D converter, input 7.

PIO2_0/DTR

1[3] yes I/O I; PU PIO2_0 — General purpose digital input/output pin.

O-

DTR — Data Terminal Ready output for UART.

PIO3_2

28[3] yes I/O I; PU PIO3_2 — General purpose digital input/output pin.

PIO3_4

13[3] no I/O I; PU PIO3_4 — General purpose digital input/output pin (LPC1311/13 only).

PIO3_5

14[3] no I/O I; PU PIO3_5 — General purpose digital input/output pin (LPC1311/13 only).

USB_DM

13[6] no I/O F

USB_DM — USB bidirectional D− line (LPC1342/43 only).

USB_DP

14[6] no I/O F

USB_DP — USB bidirectional D+ line (LPC1342/43 only).

VDD

6; -

I

-

3.3 V supply voltage to the internal regulator, the external rail, and the

29

ADC. Also used as the ADC reference voltage.

XTALIN

4[7] -

I

-

Input to the oscillator circuit and internal clock generator circuits. Input

voltage must not exceed 1.8 V.

XTALOUT

5[7] -

O-

Output from the oscillator amplifier.

VSS

33 -

-

-

Thermal pad. Connect to ground.

[1] Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (for VDD = 3.3 V, pin is pulled up to 2.6 V for

parts LPC1311/13/42/43 and pulled up to 3.3 V for parts LPC1311/01 and LPC1313/01); IA = inactive, no pull-up/down enabled.

F = floating; floating pins, if not used, should be tied to ground or power to minimize power consumption.

[2] 5 V tolerant pad. See Figure 37 for pad characteristics. RESET functionality is not available in Deep power-down mode. Use the

WAKEUP pin to reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the

Deep power-down mode.

[3] 5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see Figure 36).

[4] I2C-bus pads compliant with the I2C-bus specification for I2C standard mode and I2C Fast-mode Plus.

[5] 5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.

When configured as a ADC input, digital section of the pad is disabled, and the pin is not 5 V tolerant (see Figure 36).

[6] Pad provides USB functions. It is designed in accordance with the USB specification, revision 2.0 (Full-speed and Low-speed mode

only). This pad is not 5 V tolerant.

[7] When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded

(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.

LPC1311_13_42_43

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 5 — 6 June 2012

© NXP B.V. 2012. All rights reserved.

16 of 74

Share Link: