M35072-002FP 查看數據表（PDF） - Mitsumi
零件编号
产品描述 (功能)
生产厂家
M35072-002FP Datasheet PDF : 52 Pages
| |||
MITSUBISHI MICROCOMPUTERS
M35072-XXXFP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(7) Address 12616
DA Register
Status
Contents
Function
Remarks
0
LIN10
0
Character size setting in the vertical
The vertical dot size for line n in the character dot lines (18 vertical direction for the 10th line.
1 lines) is set using LINn (n = 2 to 17).
0
1
LIN11
Dot size can be selected between 2 types for each dot line.
1
Character size setting in the vertical
direction for the 11th line.
2
LIN12
0
For dot size, see the below registers. Line 1 and lines 2 to 12 can
be set independent of one another.
Character size setting in the vertical
direction for the 12th line.
1
0
3
LIN13
1
0
4
LIN14
1
LINn = “0”
LINn = “1”
1st line
Refer to VSZ1L0 Refer to VSZ1H0
and VSZ1L1
and VSZ1H1
2nd to 12th Refer to VSZ2L0 Refer to VSZ2H0
line
and VSZ2L1
and VSZ2H1
Character size setting in the vertical
direction for the 13th line.
Character size setting in the vertical
direction for the 14th line.
0
5
LIN15
1
0
6
LIN16
1
0
7
LIN17
1
Character size setting in the vertical
direction for the 15th line.
Character size setting in the vertical
direction for the 16th line.
Character size setting in the vertical
direction for the 17th line.
0 H: Cycle with the horizontal synchronizing pulse
8
V18SZ0
1
V18SZ1 V18SZ0 Vertical direction size
0
0
1H/dot
0
9
V18SZ1
0
1
1
0
2H/dot
3H/dot
1
1
1
4H/dot
0 H: Cycle with the horizontal synchronizing pulse
A
VSZ2L0
1
VSZ2L1 VSZ2L0 Vertical direction size
0
0
1H/dot
0
B
VSZ2L1
1
0
1
1
0
1
1
2H/dot
3H/dot
4H/dot
0 H: Cycle with the horizontal synchronizing pulse
C
VSZ2H0
1
VSZ2H1 VSZ2H0 Vertical direction size
0
0
1H/dot
0
D
VSZ2H1
1
0
1
1
0
1
1
2H/dot
3H/dot
4H/dot
Character size setting in the vertical
direction for the 18th line.
(display monitor 1 to 12 line)
Character size setting in the vertical
direction (display monitor for 2 to 12
line) at “0” state in register LIN2 to
LIN17 (address 12516, 12616).
Character size setting in the vertical
direction (display monitor for 2 to 12
line) at “0” state in register LIN2 to
LIN17 (address 12516, 12616).
0 It should be fixed to “0”.
E
TEST13
1 Can not be used.
____
Notes 1. The mark around the status value means the reset status by the "L" level is input to AC pin.
2. The page in which data is written is controlled by the DAF bit. When set to "0", data is written into page 0, whereas when set to "1",
data is written into page 1.
3. Registers marked with (Note 3) are found only in page 0, therefore the register value does not change when the DAF bit is set to "1".
14
Share Link: 