HFA1405 查看數據表（PDF） - Intersil

零件编号

产品描述 (功能)

生产厂家

HFA1405

Quad, 560MHz, Low Power, Video Operational Amplifier

Intersil 

HFA1405

Electrical Specifications VSUPPLY = ±5V, AV = +1, RF = 510Ω , RL = 100Ω , Unless Otherwise Specified (Continued)

PARAMETER

(NOTE 4)

TEST TEMP.

TEST CONDITIONS LEVEL (oC)

HFA1405IB (SOIC)

MIN TYP MAX

HFA1405IP (PDIP)

MIN TYP MAX

UNITS

Third Harmonic Distortion

(VOUT = 2VP-P, Note 5)

10MHz

20MHz

B

25

-

-63

-

-

-63

-

dBc

B

25

-

-56

-

-

-56

-

dBc

TRANSIENT CHARACTERISTICS AV = +2 (Note 3), Unless Otherwise Specified

Rise and Fall Times

(VOUT = 0.5VP-P, Note 3)

AV = +2

AV = +6

B

25

-

0.8

-

B

25

-

2.9

-

Overshoot

(VOUT = 0.5VP-P, VIN tRISE = 1ns,

Notes 3, 6)

AV = -1, +OS

AV = -1, -OS

AV = +2, +OS

B

25

-

7

-

B

25

-

8

-

B

25

-

5

-

AV = +2, -OS

B

25

-

10

-

AV = +6, +OS

B

25

-

2

-

AV = +6, -OS

B

25

-

2

-

Slew Rate

(VOUT = 5VP-P, Notes 3, 5)

AV = -1, +SR

AV = -1, -SR

B

25

-

2500

-

B

25

-

1900

-

AV = +2, +SR

B

25

-

1700

-

AV = +2, -SR

B

25

-

1700

-

AV = +6, +SR

B

25

-

1500

-

AV = +6, -SR

B

25

-

1100

-

Settling Time

(VOUT = +2V to 0V Step, Note 5)

To 0.1%

To 0.05%

B

25

-

23

-

B

25

-

30

-

-

0.9

-

-

4

-

-

3

-

-

13

-

-

7

-

-

11

-

-

2

-

-

2

-

-

2500

-

-

1900

-

-

1600

-

-

1400

-

-

1000

-

-

1000

-

-

23

-

-

30

-

ns

ns

%

%

%

%

%

%

V/µs

V/µs

V/µs

V/µs

V/µs

V/µs

ns

ns

To 0.025%

B

25

-

37

-

-

40

-

ns

Overdrive Recovery Time

VIN = ±2V

B

25

VIDEO CHARACTERISTICS AV = +2 (Note 3), Unless Otherwise Specified

Differential Gain

(f = 3.58MHz)

RL = 150Ω

RL = 75Ω

B

25

B

25

Differential Phase

(f = 3.58MHz)

RL = 150Ω

RL = 75Ω

B

25

B

25

POWER SUPPLY CHARACTERISTICS

-

8.5

-

-

0.02

-

-

0.03

-

-

0.03

-

-

0.06

-

-

8.5

-

ns

-

0.03

-

%

-

0.06

-

%

-

0.03

- Degrees

-

0.06

- Degrees

Power Supply Range

C

25

±4.5

-

±5.5 ±4.5

-

±5.5

V

Power Supply Current (Note 5)

A

25

-

5.8 6.1

-

5.8 6.1 mA/Op

Amp

A

Full

-

5.9 6.3

-

5.9 6.3 mA/Op

Amp

NOTES:

3. The optimum feedback resistor depends on closed loop gain and package type. The following resistors were used for the PDIP/SOIC charac-

terization: AV = -1, RF = 310Ω/360Ω; AV = +2, RF = 402Ω/510Ω; AV = +6, RF = 500Ω/500Ω. See the Application Information section for more

information.

4. Test Level: A. Production Tested; B. Typical or Guaranteed Limit Based on Characterization; C. Design Typical for Information Only.

5. See Typical Performance Curves for more information.

6. Undershoot dominates for output signal swings below GND (e.g., 2VP-P), yielding a higher overshoot limit compared to the VOUT = 0V to 2V

condition. See the “Application Information” section for details.

4

Share Link: