28F016S3 查看數據表（PDF） - Intel
零件编号
产品描述 (功能)
生产厂家
28F016S3 Datasheet PDF : 41 Pages
| |||
E
28F004S3/28F008S3/28F016S3
When the block erase is complete, status register
bit SR.5 should be checked. If a block erase error is
detected, the status register should be cleared
before system software attempts corrective actions.
The CUI remains in read status register mode until
a new command is issued.
This two-step command sequence of set-up
followed by execution ensures that block contents
are not accidentally erased. An invalid Block Erase
command sequence will result in both status
register bits SR.4 and SR.5 being set to “1.” Also,
reliable block erasure can only occur when
VCC = VCC2 and VPP = VPPH1/2. In the absence of
this high voltage, block contents are protected
against erasure. If block erase is attempted while
VPP ≤ VPPLK, SR.3 and SR.5 will be set to “1.”
Successful block erase requires that the
corresponding block lock-bit be cleared or, if set,
that RP# = VHH. If block erase is attempted when
the corresponding block lock-bit is set and
RP# = VIH, the block erase will fail, and SR.1 and
SR.5 will be set to “1.” Block erase operations with
VIH < RP# < VHH produce spurious results and
should not be attempted.
4.6 Program Command
Program is executed by a two-cycle command
sequence. Program setup (standard 40H or
alternate 10H) is written, followed by a second write
that specifies the address and data (latched on the
rising edge of WE#). The WSM then takes over,
controlling the program and verify algorithms
internally. After the program sequence is written,
the device automatically outputs status register
data when read (see Figure 8). The CPU can detect
the completion of the program event by analyzing
the RY/BY# pin or status register bit SR.7.
When program is complete, status register bit SR.4
should be checked. If program error is detected, the
status register should be cleared. The internal WSM
verify only detects errors for “1”s that do not
successfully program to “0”s. The CUI remains in
read status register mode until it receives another
command.
Reliable program only occurs when VCC = VCC2 and
VPP = VPPH1/2. In the absence of this high voltage,
memory contents are protected against program
operations. If a program operation is attempted
while VPP ≤ VPPLK, the operation will fail, and status
register bits SR.3 and SR.5 will be set to “1.”
PRELIMINARY
A successful program operation also requires that
the corresponding block lock-bit be cleared or, if
set, that RP# = VHH. If a program operation is
attempted when the corresponding block lock-bit is
set and RP# = VIH, the operation will fail, and SR.1
and SR.4 will be set to “1.” Program operations with
VIH < RP# < VHH produce spurious results and
should not be attempted.
4.7 Block Erase Suspend
Command
The Block Erase Suspend command allows
block-erase interruption to read or program data in
another block of memory. Once the block erase
process starts, writing the Block Erase Suspend
command requests that the WSM suspend the
block erase sequence at a predetermined point in
the algorithm. The device outputs status register
data when read after the Block Erase Suspend
command is written. Polling status register bits
SR.7 and SR.6 can determine when the block erase
operation has been suspended (both will be set to
“1”). RY/BY# will also transition to VOH.
Specification tWHRH2 defines the block erase
suspend latency.
At this point, a Read Array command can be written
to read data from blocks other than that which is
suspended. A Program command sequence can
also be issued during erase suspend to program
data in other blocks. Using the Program Suspend
command (see Section 4.8), a program operation
can also be suspended. During a program operation
with block erase suspended, status register bit
SR.7 will return to “0” and the RY/BY# output will
transition to VOL. However, SR.6 will remain “1” to
indicate block erase suspend status.
The only other valid commands while block erase is
suspended are Read Status Register and Block
Erase Resume. After a Block Erase Resume
command is written to the flash memory, the WSM
will continue the block erase process. Status
register bits SR.6 and SR.7 will automatically clear
and RY/BY# will return to VOL. After the Erase
Resume command is written, the device
automatically outputs status register data when
read (see Figure 9). VPP must remain at VPPH1/2
(the same VPP level used for block erase) while
block erase is suspended. RP# must also remain at
VIH or VHH (the same RP# level used for block
erase). Block erase cannot resume until program
operations initiated during block erase suspend
have completed.
17
Share Link: 