TC850CLW 查看數據表（PDF） - TelCom Semiconductor Inc => Microchip
零件编号
产品描述 (功能)
生产厂家
TC850CLW
TelCom Semiconductor Inc => Microchip
TC850CLW Datasheet PDF : 14 Pages
| |||
15-BIT, FAST-INTEGRATING CMOS
ANALOG-TO-DIGITAL CONVERTER
1
TC850
Digital Operating Modes
Two modes of operation are available with the TC850,
continuous conversions and on-demand. The operating
mode is controlled by the CONT/DEMAND input. The bus
interface method is different for continuous and demand
modes of operation.
Demand Mode Operation
When CONT/DEMAND is low, the TC850 performs one
conversion each time the chip is selected and the WR input
is pulsed low. Data is valid on the falling edge of the BUSY
output and can be accessed using the interface truth table
(Table 1).
Continuous Mode Operation
2 When CONT/DEMAND is high, the TC850 continuously
performs conversions. Data will be valid on the falling edge
of the BUSY output, and remains valid for 443-1/2 clock
cycles.
The low/high (L/H) byte-select and overrange/polarity
(OVR/POL) inputs are disabled during continuous mode
operation. Data must be read in three consecutive bytes, as
shown in Table I.
NOTE: In continuous mode, the conversion result must be read within 443-
1/2 clock cycles of the BUSY output falling edge. After this time (i.e., 1/2
clock cycle before BUSY goes high) the internal counters are reset and the
data is lost.
3
Table 1. Bus Interface Truth Table
CE•CS
RD CONT/DEMAND
L/H OVR/POL
DB7
DB6–DB0
Pins 1 and 2
0
0
0
0
0
1
Pin 4
0
0
0
0
1
X
Pin 5
0
0
0
1
X
X
Pin 7
0
0
1
X
X
X
Pin 6
0
1
X
X
X
X
Pin 8
"1" = Input Positive
"1" = Input Overrange
(Note 2)
Data Bit 7
Note 3
High-Impedance State
High-Impedance State
Pin 9-Pin 15 (Note 1)
Data Bits 14 – 8
Data Bits 14 – 8
Data Bits 6 – 0
NOTES: 1. Pin numbers refer to 40-pin DIP.
2. Extended overrange operation: Although rated at 15 bits (±32,767 counts) of resolution, the TC850 provides an additional 191 counts
above full scale. For example, with a full-scale input of 3.2768V, the maximum analog input voltage which will be properly converted is
3.2958V. The extended resolution is signified by the overrange bit being high and the low-order byte contents being between 0 and 190.
For example, with a full-scale voltage of 3.2768V:
VIN
3.2767V
3.2768V
3.2769V
3.2867V
Overrange Bit
Low
High
High
High
Low Byte
25510
00010
00110
09910
Data Bits 14–8
12710
010
010
010
3. Continuous mode data transfer:
a. In continuous mode, data MUST be read in three sequential bytes after the BUSY output goes low:
(1) The first byte read will be the high-order byte, with DB7 = polarity.
(2) The second byte read will contain the low-order byte.
(3) The third byte read will again be the high-order byte, but with DB7 = overrange.
b. All three data bytes must be read within 443-1/2 clock cycles after the falling edge of BUSY.
c. The RD input must go high after each byte is read, so that the internal byte counter will be incremented. However, the CS and CE
inputs can remain enabled through the entire data transfer sequence.
4
5
6
7
TELCOM SEMICONDUCTOR, INC.
8
3-85
Share Link: