CY7C1316JV18 查看數據表（PDF） - Cypress Semiconductor
零件编号
产品描述 (功能)
生产厂家
CY7C1316JV18 Datasheet PDF : 26 Pages
| |||
CY7C1316JV18, CY7C1916JV18
CY7C1318JV18, CY7C1320JV18
Truth Table
The truth table for the CY7C1316JV18, CY7C1916JV18, CY7C1318JV18, and CY7C1320JV18 follows. [2, 3, 4, 5, 6, 7]
Operation
K
LD
Write Cycle:
L-H
L
Load address; wait one cycle;
input write data on consecutive K and K rising edges.
Read Cycle:
Load address; wait one and a half cycle;
read data on consecutive C and C rising edges.
L-H
L
NOP: No Operation
L-H
H
Standby: Clock Stopped
Stopped
X
R/W
DQ
DQ
L D(A1) at K(t + 1) ↑ D(A2) at K(t + 1) ↑
H Q(A1) at C(t + 1)↑ Q(A2) at C(t + 2) ↑
X High-Z
High-Z
X Previous State Previous State
Burst Address Table
(CY7C1318JV18, CY7C1320JV18)
First Address (External)
X..X0
X..X1
Second Address (Internal)
X..X1
X..X0
Write Cycle Descriptions
The write cycle description table for CY7C1316JV18 and CY7C1318JV18 follows. [2, 8]
BWS0/ BWS1/ K
K
NWS0 NWS1
Comments
L
L L–H – During the data portion of a write sequence:
CY7C1316JV18 − both nibbles (D[7:0]) are written into the device.
CY7C1318JV18 − both bytes (D[17:0]) are written into the device.
L
L
– L-H During the data portion of a write sequence:
CY7C1316JV18 − both nibbles (D[7:0]) are written into the device.
CY7C1318JV18 − both bytes (D[17:0]) are written into the device.
L
H L–H – During the data portion of a write sequence:
CY7C1316JV18 − only the lower nibble (D[3:0]) is written into the device, D[7:4] remains unaltered.
CY7C1318JV18 − only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
L
H
– L–H During the data portion of a write sequence:
CY7C1316JV18 − only the lower nibble (D[3:0]) is written into the device, D[7:4] remains unaltered.
CY7C1318JV18 − only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
H
L L–H – During the data portion of a write sequence:
CY7C1316JV18 − only the upper nibble (D[7:4]) is written into the device, D[3:0] remains unaltered.
CY7C1318JV18 − only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
H
L
– L–H During the data portion of a write sequence:
CY7C1316JV18 − only the upper nibble (D[7:4]) is written into the device, D[3:0] remains unaltered.
CY7C1318JV18 − only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
H
H L–H – No data is written into the devices during this portion of a write operation.
H
H
– L–H No data is written into the devices during this portion of a write operation.
Notes
2. X = “Don’t Care,” H = Logic HIGH, L = Logic LOW, ↑ represents rising edge.
3. Device powers up deselected with the outputs in a tri-state condition.
4. On CY7C1318JV18 and CY7C1320JV18, “A1” represents address location latched by the devices when transaction was initiated and “A2” represents the addresses
sequence in the burst. On CY7C1316JV18 and CY7C1916JV18, “A1” represents A + ‘0’ and “A2” represents A + ‘1’.
5. “t” represents the cycle at which a read/write operation is started. t + 1 and t + 2 are the first and second clock cycles succeeding the “t” clock cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.
7. It is recommended that K = K and C = C = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging
symmetrically.
8. Is based on a write cycle that was initiated in accordance with the Write Cycle Descriptions table. NWS0, NWS1, BWS0, BWS1, BWS2, and BWS3 can be altered on
different portions of a write cycle, as long as the setup and hold requirements are achieved.
Document Number: 001-15271 Rev. *B
Page 10 of 26
[+] Feedback
Share Link: 