DMS-30LCD 查看數據表（PDF） - Murata Power Solutions
零件编号
产品描述 (功能)
生产厂家
DMS-30LCD Datasheet PDF : 6 Pages
| |||
APPLICATIONS
2. Differential Input Configurations: Differential measurements can be
made with either 5V-powered or 9V-powered meters. Figure 3, though
not a practical real-world application, uses a voltage divider to demon-
strate the concept of a differential input signal. Be careful not to exceed
the ±2V common mode voltage limitation for 5V-powered meters.
REF OUT 8
REF IN 7
DP1 6
DMS-30LCD-1-5
R1
11
1k
(+) IN HI
1
+5V SUP
R2
12
1k
(–) IN LO
R3
3
1k
5V RET
120 VAC
AC to DC Converter
Figure 3. Differential Input Configuration
(5V-Powered Models)
3. Engineering Scaling: For measuring voltages greater than the full
scale input range of a given meter, the input signal must be attenuated.
A simple voltage divider (similar to that shown in Figure 4) will scale
the input to within the range of the selected meter. R1 and R2 should
be precision, ±1%, metal-film resistors with absolute TCR’s less than
50ppm/°C. See Ap Note 4 for more information on engineering scaling.
50kΩ < R1 + R2 < 10MΩ
R2 x VIN = Reading
R1 + R2
R1
VIN
11
(+) IN HI
R2
12
(–) IN LO
–
DMS-30LCD-1-5
1
+5V SUP
3
5V RET
8
REF OUT
7
REF IN
120 VAC
AC to DC Converter
Figure 4. Input Attenuation Circuit
www.murata-ps.com/support
DMS-30LCD Series
3½ Digit, LCD Display Digital Panel Voltmeters
4. Floating Signal Source Measurements: Floating signals can be
measured using the circuits shown in Figures 5 and 6. Figure 5 uses
a 5V-powered meter. Figure 6 uses a 9V-powered meter. Connecting
pin 10 (ANALOG COMMON) to (–) INPUT LO (pin 12) provides the
reference point for the meter’s input.
A “floating” input is a signal that has no galvanic connection to the
meter’s power supply. In the figures below, the 1.5V battery illustrates a
true floating input.
1.5V
CELL
–
11
(+) IN HI
10
ANA COMM
DMS-30LCD-1-5
8
REF OUT
12
(–) IN LO
1
+5V SUP
3
5V RET
7
REF IN
6
DP1
120 VAC
AC to DC Converter
Figure 5. Floating Input Measurements
(5V-Powered Models)
1.5V
CELL
–
11
(+) IN HI
10
ANA COMM
12
(–) IN LO
1
+ BAT
DMS-30LCD-1-9
3
–BAT
9V
BATTERY
–
8
REF OUT
7
REF IN
6
DP1
Figure 6. Floating Input Measurements
(9V-Powered Models)
5. Process Control (4-to-20mA) Measurements: In many common
process-control applications, a 4-to-20mA current loop is used to
transmit information. Because DMS-30LCD meters have such high
input impedance, a simple shunt resistor across the meter’s input can
be used to convert the loop current to a voltage. See Figure 7. The
value of the shunt resistor is a function of the scaling requirements of
the particular application and can be calculated using the following
equation:
MPM_DMS30LCD.E01 Page 4 of 6
Share Link: 