OR4E10 查看數據表（PDF） - Agere -> LSI Corporation

零件编号

产品描述 (功能)

生产厂家

OR4E10

ORCA® Series 4 Field-Programmable Gate Arrays

Agere -> LSI Corporation 

Preliminary Data Sheet

December 2000

ORCA Series 4 FPGAs

Routing Resources

The abundant routing resources of the Series 4 archi-

tecture are organized to route signals individually or as

buses with related control signals. Both local and global

signals utilize high-speed buffered and nonbuffered

routes. One PLC segmented (x1), six PLC segmented

(x6), and bused half-chip (xHL) routes are patterned

together to provide high connectivity with fast software

routing times and high-speed system performance.

x1 routes cross width of one PLC and provide local

connectivity to PFU and SLIC inputs and outputs. x6

lines cross width of six PLCs and are unidirectional and

buffered with taps in the middle and on the end. Seg-

ments allow connectivity to PFU/SLIC outputs (driven

at one endpoint), other x6 lines (at endpoints), and

x1 lines for access to PFU/SLIC inputs. xH lines run

vertically and horizontally the distance of half the

device and are useful for driving medium-/long-dis-

tance 3-state routing.

The improved routing resources offer great flexibility in

moving signals to and from the logic core. This flexibil-

ity translates into an improved capability to route

designs at the required speeds even when the I/O sig-

nals have been locked to specific pins.

Generally, the ORCA Foundry Development System is

used to automatically route interconnections. Interac-

tive routing with the ORCA Foundry design editor

(EPIC) is also available for design optimization.

The routing resources consist of switching circuitry and

metal interconnect segments. Generally, the metal lines

which carry the signals are designated as routing seg-

ments. The switching circuitry connects the routing

segments, providing one or more of three basic func-

tions: signal switching, amplification, and isolation. A

net running from a PFU or PIO output (source) to a

PLC or PIO input (destination) consists of one or more

routing segments, connected by switching circuitry

called configurable interconnect points (CIPs).

Clock Distribution Network

Primary Clock Nets

The Series 4 FPGAs provide eight fully distributed glo-

bal primary net routing resources. These eight primary

nets can only drive clock signals. The scheme dedi-

cates four of the eight resources to provide fast primary

nets and four are available for general primary nets.

The fast primary nets are targeted toward low-skew

and small injection times while the general primary

nets are also targeted toward low-skew but have more

source location flexibility. Fast access to the global pri-

mary nets can be sourced from two pairs of pads

Lucent Technologies Inc.

located in the center of each side of the device, from

the programmable PLLs, and dedicated network PLLs

located in the corners, or from PLC logic. The I/O pads

are dedicated in pairs for use of differential I/O clocking

or single-ended I/O clock sources. However, if these

pads are not needed to source the clock network, they

can be utilized for general I/O. The clock routing

scheme is patterned using vertical and horizontal

routes which provide connectivity to all PLC columns.

Secondary Clock and Control Nets

Secondary spines provide flexible clocking and control

signaling for local regions. Secondary nets usually

have high fan-outs. The Series 4 utilizes a spine and

branches that use additional x6 segments. This strat-

egy provides a flexible connectivity and routes can be

sourced from any I/O pin, all PLLs, or from PLC logic.

Edge Clock Nets

Routes are distributed around the edges and are avail-

able for every four PIOs (one per PIC). All PIOs and

PLLs can drive the edge clocks and are used in con-

junction with the secondary spines discussed above to

drive the same edge clock signal into the internal logic

array. The edge clocks provide fast injection to the PLC

array and I/O registers. Many edge clock nets are pro-

vided on each side of the device.

Programmable Input/Output Cells

Programmable I/O

The Series 4 PIO addresses the demand for the flexi-

bility to select I/O that meets system interface require-

ments. I/Os can be programmed in the same manner

as in previous ORCA devices with the addition of new

features that allow the user the flexibility to select new

I/O types that support high-speed interfaces.

Each PIC contains up to four programmable I/O pads

and are interfaced through a common interface block to

the FPGA array. The PIO group is split into two pairs of

I/O pads with each pair having independent clock

enables, local set/reset, and global set/reset.

On the input side, each PIO contains a programmable

latch/FF which enables very fast latching of data from

any pad. The combination provides for very low setup

requirements and zero hold times for signals coming

on-chip. It may also be used to demultiplex an input sig-

nal, such as a multiplexed address/data signal, and

register the signals without explicitly building a demulti-

plexer with a PFU.

31

Share Link: