Absolute Maximum Ratings(Note 1)
Storage Temperature (TSTG)
Maximum Junction Temperature (TJ)
Case Temperature under Bias (TC)
VEE Pin Potential to Ground Pin
VTTL Pin Potential to Ground Pin
ECL Input Voltage (DC)
TTL Input Voltage
Output Current
(DC Output HIGH)
ESD (Note 2)
−65°C to +150°C
+150°C
0°C to +85°C
−7.0V to +0.5V
−0.5V to +6.0V
VEE to +0.5V
−0.5V to +7.0V
+130 mA
≥ 2000V
Recommended Operating
Conditions
Case Temperature (TC)
Supply Voltage
0°C to +85°C
VEE
−5.7V to −4.2V
VTTL
+4.5V to +5.5V
Note 1: The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
Note 2: ESD testing conforms to MIL-STD-883, Method 3015.
Commercial Version
DC Electrical Characteristics (Note 3)
VEE = −4.2V to −5.7V, VCC = VCCA = GND, TC = 0°C to +85°C
Symbol
Parameter
Min
Typ
Max
Units
Conditions
VOH
Output HIGH Voltage
2.4
V
IOH = −15 mA
VIN = VIH (Max)
VOL
Output LOW Voltage
0.55
V
IOL = 64 mA
or VIL (Min)
VIH
Input HIGH Voltage
−1165
−870
mV Guaranteed HIGH Signal for All Inputs
VIL
Input LOW Voltage
−1830
−1475
mV Guaranteed LOW Signal for All Inputs
IIL
Input LOW Current
0.5
µA
VIN = VIL (Min)
IIH
Input HIGH Current
240
µA
VIN = VIH (Max)
IOZL
3-STATE Current Output HIGH
−50
µA
VOUT = +0.4V
IOZH
3-STATE Current Output LOW
+50
µA
VOUT = +2.7V
ICEX
Output HIGH Leakage Current
250
µA
VOUT = VCC
IOS
Output Short-Circuit Current
−100
−225
mA
IEE
VEE Power Supply Current
−67
−29
mA Inputs OPEN
ICCH
VTTL Power Supply Current HIGH
29
mA
ICCL
VTTL Power Supply Current LOW
65
mA
ICCZ
VTTL Power Supply Current 3-STATE
49
mA
Note 3: The specified limits represent the “worst case” value for the parameter. Since these values normally occur at the temperature extremes, additional
noise immunity and guardbanding can be achieved by decreasing the allowable system operating ranges. Conditions for testing shown in the tables are cho-
sen to guarantee operation under “worst case” conditions.
PLCC AC Electrical Characteristics
VEE = −4.2V to −5.7V, VCC = GND, VTTL = +4.5V to +5.5V
Symbol
Parameter
TC = 0°C
Min
Max
tPLH
Propagation Delay
tPHL
Clock to Output
tPZL
Output Enable Time
tPZH
OE ↓ to QN
tPLZ
Output Disable Time
tPHZ
OE ↑ to QN
2.30
5.00
3.00
5.60
3.20
7.60
2.40
5.60
3.20
7.60
2.40
5.60
tH
Data to CP EN
1.5
Hold Time
1.5
tS
Data to CP EN
0.5
Setup Time
0.5
tPW(H)
Clock Pulse Width
2.0
TC = +25°C
Min
Max
2.30
5.00
3.00
5.60
3.20
7.60
2.40
5.60
3.20
7.60
2.40
5.60
1.5
1.5
0.5
0.5
2.0
TC = +85°C
Min
Max
2.30
5.00
3.40
6.40
3.20
7.60
2.40
5.60
3.20
7.60
2.40
5.60
1.5
1.5
0.5
0.5
2.0
Units
Conditions
ns Figures 1, 2
ns Figures 1, 3
ns Figures 1, 3
ns Figures 1, 2
ns Figures 1, 2
ns Figures 1Figure 2
3
www.fairchildsemi.com