AD6122ACP 查看數據表（PDF） - Analog Devices
零件编号
产品描述 (功能)
生产厂家
AD6122ACP Datasheet PDF : 20 Pages
| |||
AD6122
The AD6122’s overall gain, expressed in decibels, is linear in
dB with respect to the automatic gain control (AGC) voltage,
VGAIN. Either REFOUT or an external reference voltage con-
nected to REFIN may be used to set the voltage range for VGAIN.
When the internal 1.23 V reference, REFOUT, is connected to
REFIN , VGAIN will control the entire AGC range when it is
typically set between 0.5 V and 2.5 V. Minimum gain occurs at
minimum voltage on VGAIN and maximum gain occurs at maxi-
mum voltage on VGAIN. The maximum and minimum gain
will not change with a change in voltage at REFIN. Rather, the
slope of the gain curve will change as a result of a change in the
required range for VGAIN. Figure 24 shows the piecewise linear
approximation of the gain curve for the AD6122.
MAXIMUM
GAIN
MINIMUM
GAIN
VGAIN – V
Figure 24. Piecewise Linear Approximation for the
AD6122 Gain Curve
Because the minimum and maximum gain from the AD6122
are constant, we can approximate the VGAIN range for a
given REFIN voltage by using Equation 1.
VGAIN = (GAIN – MinGain) × 1.6REFIN + 0.4 REFIN (1)
MaxGain – MinGain
Where MaxGain is the maximum gain (+34 dB) in dB, MinGain
is the minimum gain (–63 dB) in dB, REFIN is the reference
input voltage, in volts, VGAIN is the gain control voltage input,
in volts, and GAIN is the particular gain, in dB, we would have
for a given REFIN and VGAIN. Consequently, for any REFIN
we choose, we can calculate the VGAIN range by solving
Equation 1 for VGAIN. For example, in order to determine the
VGAIN value for the maximum gain condition, given a 1.23 V
REFIN, we can solve Equation 1 for VGAIN by substituting
+34 dB for GAIN and MaxGain, –63 dB for MinGain and 1.23 V
for REFIN. VGAIN can then be calculated to be 2.46 V, or
approximately 2.5 V. For the minimum gain condition, we can
determine the VGAIN value by substituting 34 dB for MaxGain,
–63 dB for GAIN and MinGain and 1.23 V for REFIN. VGAIN
can then be calculated to be 0.492 V or approximately 0.5 V.
Power-Down Control
The AD6122 can be operated with the IF amplifiers and quadra-
ture modulator both powered up, both powered down or with
the IF amplifiers powered up and the modulator powered down.
The AD6122 cannot operate with only the modulator powered
up. The control is provided via two control pins, PD1 and PD2.
Table I shows the operating modes of the AD6122.
PD1
0
0
1
1
Table I. Operating Modes
PD2 IF Amp
Modulator
0
ON
ON
1
ON
OFF
0
INVALID STATE INVALID STATE
1
OFF
OFF
Low Dropout Regulator
The AD6122 incorporates an integrated low dropout regulator.
The regulator accepts inputs from 2.9 V to 4.2 V and supplies a
constant 2.7 V reference output at LDOC. The 2.7 V signal can
be used to provide the dc voltages required for the DVCC,
TXVCC and IFVCC dc supplies. In order to configure the low
dropout regulator, an external pass transistor is required. A pnp
bipolar junction transistor with a minimum hFE of 100 and a
maximum hFE of 300 and a VCESAT of –0.4 V is required. In
order to use the low dropout regulator, configure the transistor as
shown in Figure 25. The 18 pF capacitor in Figure 25 is used for
decoupling the 2.7 V dc signal.
In addition to the low dropout regulator, a band-gap voltage
reference produces a 1.23 V reference voltage at REFOUT.
This reference voltage will be present whenever a 2.7 V dc sig-
nal is present on pin LDOC. This 1.23 V reference voltage can
then be used to provide the gain reference signal required for
REFIN and the reference voltage for the transmit DACs in a
baseband converter.
2.9V – 4.2V
PASS
TRANSISTOR
2.7V
18pF
AD6122
LDOE
LDOB
LDOC
REFOUT
1.23V
Figure 25. Configuring the Low Dropout Regulator
It is possible to bypass the low dropout regulator on the AD6122
and use an external regulator instead. In order to bypass the
integrated low dropout regulator, connect pins LDOE, LDOB
and LDOC together and then connect them all to the 2.7 V
external regulator voltage. This configuration is shown in
Figure 26. Even when the low dropout regulator is bypassed,
the 1.23 V reference voltage at pin REFOUT is still present.
–12–
REV. B
Share Link: 