ADV7129 查看數據表（PDF） - Analog Devices

零件编号

产品描述 (功能)

生产厂家

ADV7129

192-Bit, 360 MHz True-Color Video DAC with Onboard PLL

Analog Devices 

ADV7129

PIN DESCRIPTION

Mnemonic

Function

R7–R0[A . . . H]

G7–G0[A . . . H]

B7–B0[A . . . H]

BLANK

ODD/EVEN

HSYNC

VSYNC

CSYNC

CE

R/W

C0, C1

D7–D0

LOADIN

LOADOUT

LPF

Red Pixel Port Inputs (TTL Compatible Inputs). Eight sets of eight bits latched on the rising edge of

LOADIN.

Green Pixel Port Inputs (TTL Compatible Inputs). Eight sets of eight bits latched on the rising edge of

LOADIN.

Blue Pixel Port Inputs (TTL Compatible Inputs). Eight sets of eight bits latched on the rising edge of

LOADIN.

Composite Blank (TTL Compatible Input). This video control signal drives the analog outputs to the blanking

level. When BLANK is at logic “0,” the pixel inputs are ignored. Pedestal selection is controlled by Bit CR15

of Command Register 1. BLANK is latched on the rising edge of LOADIN.

Odd/Even Field Input (TTL Compatible Input). This input indicates which field of the frame is being dis-

played. An even field is selected by setting ODD/EVEN to logical “0.” An odd field is selected by setting

ODD/EVEN to logical “1.” ODD/EVEN should be changed only during vertical blank.

Horizontal-Sync Input (TTL Compatible Input). This control signal is latched on the rising edge of LOADIN.

Vertical-Sync Input (TTL Compatible Input). This control signal is latched on the rising edge of LOADIN.

Composite-Sync Input (TTL Compatible Input). This video control signal drives the analog outputs to the

SYNC level. It is only asserted during the blanking period and does not override any other control or data in-

put. CR14, CR13 or CR12 of Command Register 1 must be set together with CR11 or Command Register 1 to

decode SYNC onto the IOR/IOR, IOG/IOG or IOB/IOB analog outputs, otherwise the SYNC input is ignored.

Chip Enable Input (TTL Compatible Input). This input must be set to logic “0” when writing or reading over

the data bus (D7–D0). Internally, data is latched on the rising edge of CE.

Read/Write pin (TTL Compatible Input). This signal is latched on the falling edge of CE. A high level indi-

cates a read operation and a low level indicates a write operation.

Register select pins (TTL Compatible Inputs). These inputs select which MPU port register is selected for

writing or reading. Data is latched on the falling edge of CE.

Data Bus (TTL Compatible Input/Output Bus). Data, including color palette values and device control infor-

mation is written to and read from the device over this 8-bit, bidirectional databus. Any unused bits of the

data bus should be terminated through a resistor to either the digital power plane (VCC) or GND.

Pixel Data Load Input (TTL Compatible Input). This input latches the multiplexed pixel data, including

BLANK, HSYNC, VSYNC, CSYNC, and ODD/EVEN into the device. This rising edge of this signal is used

to latch in the video signal inputs. It is also used as a reference frequency to generate an 8 × multiple pixel

clock using the fixed reference onboard PLL.

Pixel Data Load Output (TTL Compatible Output). This digital output is PCLK/8. If the onboard phase lock

loop is used, it has the same phase as LOADIN.

Low-Pass Filter Pin. This pin stabilizes the internal PLL. The following network is recommended.

VAA

0.1µF

100Ω

0.001µF

LPF

Figure 5.

–8–

REV. 0

Share Link: