DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

CGY2014ATW 查看數據表(PDF) - Philips Electronics

零件编号
产品描述 (功能)
生产厂家
CGY2014ATW
Philips
Philips Electronics Philips
CGY2014ATW Datasheet PDF : 12 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Philips Semiconductors
GSM/DCS/PCS power amplifier
Preliminary specification
CGY2014ATW
AC CHARACTERISTICS
VDD1 = 2.8 V; VDD2 = VDD3 = 3.5 V; Tamb = 25 °C; measured on the Philips application diagram (see Fig.3).
SYMBOL
PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
Low band: GSM power amplifier
Pi(LB)
input power
fRF(LB)
RF frequency range
Po(LB)(max)
ηLB
maximum output power
efficiency
Po(LB)(min) minimum output power
VDD = 0 V; Pi(LB) = 5 dBm
NRX(LB)
output noise in RX band Pi(LB) = 5 dBm
fRF = 925 to 935 MHz
fRF = 935 to 960 MHz
H2LB
2nd harmonic level
Pi(LB) = 5 dBm
H3LB
3rd harmonic level
Pi(LB) = 5 dBm
StabLB
stability
Pi(LB) = 5 dBm; note 1
High band: DCS/PCS power amplifier; note 2
3
5
880
34.5 35
50
55
30
7
dBm
915 MHz
dBm
%
dBm
117
129
35
35
60
dBm/Hz
dBm/Hz
dBc
dBc
dBc
Pi(HB)
fRF(HB)
Po(HB)(max)
ηHB
Po(HB)(min)
αHB
NRX(HB)
H2HB
H3HB
StabHB
input power
RF frequency range
maximum output power
efficiency
minimum output power
high band isolation when
low band is operating
output noise in RX band
2nd harmonic level
3rd harmonic level
stability
for DCS operation
VDD = 0 V; Pi(HB) = 5 dBm
VDD(LB) = 3.5 V; Pi(LB) = 5 dBm;
VDD(HB) = 0 V; Pi(HB) = 5 dBm;
note 3
Pi(HB) = 5 dBm
Pi(HB) = 5 dBm
Pi(HB) = 5 dBm
Pi(HB) = 5 dBm; note 1
3
5
1710
32
32.5
38
40
30
0
7
1 785
dBm
MHz
dBm
%
dBm
dBm
121 dBm/Hz
35 dBc
35 dBc
60 dBc
Notes
1. The device is adjusted to provide nominal load power into a 50 load. The device is switched off and a 6 : 1 load
replaces the 50 load. The device is switched on and the phase of the 6 : 1 load is varied 360 electrical degrees
during a 60 seconds test period.
2. The power amplifier can be matched to PCS and/or DCS/PCS operation through optimization of the matching circuit;
see Application Note (tbf).
3. Isolation can be improved to 20 dBm (typical) with a pin diode switched in the DCS output matching circuit.
2000 Nov 28
6

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]