CY14B101L(2007) 查看數據表（PDF） - Cypress Semiconductor
零件编号
产品描述 (功能)
生产厂家
CY14B101L Datasheet PDF : 18 Pages
| |||
PRELIMINARY
CY14B101L
Maximum Ratings
Exceeding maximum ratings may shorten the device battery
life. These user guidelines are not tested.
Storage Temperature .................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Supply Voltage on VCC Relative to GND ......... –0.5V to 4.1V
Voltage Applied to Outputs
in High-Z State .......................................–0.5V to VCC + 0.5V
Input Voltage ..........................................–0.5V to VCC + 0.5V
Transient Voltage (<20 ns) on
Any Pin to Ground Potential ..................–2.0V to VCC + 2.0V
Package Power Dissipation
Capability (TA = 25°C) ................................................... 1.0W
Surface Mount Lead Soldering
Temperature (three seconds) .................................... +260°C
Output Short Circuit Current [4].................................... 15 mA
Static Discharge Voltage.......................................... > 2001V
(in accordance with MIL-STD-883, method 3015)
Latch up Current.................................................... > 200 mA
Operating Range
Range
Commercial
Industrial
Ambient Temperature
0°C to +70°C
–40°C to +85°C
VCC
2.7V to 3.6V
2.7V to 3.6V
DC Electrical Characteristics
Over the Operating Range (VCC = 2.7V to 3.6V) [5, 6, 7]
Parameter
Description
Test Conditions
Min
Max
Unit
ICC1
Average VCC Current tRC = 25 ns
Commercial
tRC = 35 ns
tRC = 45 ns
Dependent on output loading and cycle rate.
Values obtained without output loads.
Industrial
IOUT = 0 mA.
ICC2
Average VCC Current All inputs do not care, VCC = Max
during STORE
Average current for duration tSTORE
ICC3
Average VCC Current at WE > (VCC – 0.2). All other inputs cycling.
tAA = 200 ns, 3V, 25°C Dependent on output loading and cycle rate.
typical
Values obtained without output loads. IOUT = 0 mA.
ICC4
Average VCAP Current All inputs do not care, VCC = Max
during AutoStore Cycle Average current for duration tSTORE
ISB
VCC Standby Current WE > (VCC – 0.2). All others VIN < 0.2V or > (VCC – 0.2V).
Standby current level after nonvolatile cycle is complete.
Inputs are static. f = 0 MHz.
65
mA
55
mA
50
mA
55
mA
(tRC = 45 ns)
6
mA
10
mA
3
mA
3
mA
IIX
IOZ
VIH
VIL
VOH
VOL
VCAP
Input Leakage Current VCC = Max, VSS < VIN < VCC
Off State Output
Leakage Current
VCC = Max, VSS < VIN < VCC, CE or OE > VIH
Input HIGH Voltage [7]
Input LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Storage Capacitor
IOUT = –2 mA
IOUT = 4 mA
Between VCAP pin and VSS, 5V rated
–1
+1
µA
–1
+1
µA
2.0 Vcc + 0.3 V
Vss – 0.5 0.8
V
2.4
V
0.4
V
17
120
µF
Notes
4. Outputs shorted for no more than one second. No more than one output shorted at a time.
5. Typical conditions for the active current shown on the front page of the data sheet are average values at 25°C (room temperature), and VCC = 3V. Not 100% tested.
6. The HSB pin has IOUT = –10 µA for VOH of 2.4 V, this parameter is characterized but not tested.
7. VIH changes by 100 mV when VCC > 3.5V.
Document #: 001-06400 Rev. *E
Page 7 of 18
[+] Feedback
Share Link: 