EN29F080(2000) 查看數據表（PDF） - Eon Silicon Solution Inc.

零件编号

产品描述 (功能)

生产厂家

EN29F080
(Rev.:2000)

8 Megabit (1024K x 8-bit) Flash Memory

Eon Silicon Solution Inc. 

EN29F080

verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required

to provide any controls or timings during these operations. The Command Definitions table shows the

address and data requirements for the chip erase command sequence.

Any commands written to the chip during the Embedded Erase algorithm are ignored.

The system can determine the status of the erase operation by using DQ7, DQ6, or DQ2. See “Write

Operation Status” for information on these status bits. When the Embedded Erase algorithm is complete,

the device returns to reading array data and addresses are no longer latched.

Flowchart 4 illustrates the algorithm for the erase operation. See the Erase/Program Operations tables in

“AC Characteristics” for parameters, and to the Chip/Sector Erase Operation Timings for timing

waveforms.

Sector Erase Command Sequence

Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two

un-lock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by

the address of the sector to be erased, and the sector erase command. The Command Definitions table

shows the address and data requirements for the sector erase command sequence.

Once the sector erase operation has begun, only the Erase Suspend command is valid. All other

commands are ignored.

When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses

are no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, or

DQ2. Refer to “Write Operation Status” for information on these status bits. Flowchart 4 illustrates the

algorithm for the erase operation. Refer to the Erase/Program Operations tables in the “AC

Characteristics” section for parameters, and to the Sector Erase Operations Timing diagram for timing

waveforms.

Erase Suspend / Resume Command

The Erase Suspend command allows the system to interrupt a sector erase operation and then read data

from, or program data to, any sector not selected for erasure. This command is valid only during the

sector erase operation. The Erase Suspend command is ignored if written during the chip erase operation

or Embedded Program algorithm. Writing the Erase Suspend command during the Sector Erase time-out

immediately terminates the time-out period and suspends the erase operation. Addresses are don’t-cares

when writing the Erase Suspend command.

When the Erase Suspend command is written during a sector erase operation, the device requires a

maximum of 20 µs to suspend the erase operation. However, when the Erase Suspend command is

written during the sector erase time-out, the device immediately terminates the time-out period and

suspends the erase operation.

After the erase operation has been suspended, the system can read array data from or program data to

any sector not selected for erasure. (The device “erase suspends” all sectors selected for erasure.)

Normal read and write timings and command definitions apply. Reading at any address within erase-

suspended sectors produces status data on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2

together, to determine if a sector is actively erasing or is erase-suspended. See “Write Operation Status”

for information on these status bits.

After an erase-suspended program operation is complete, the system can once again read array data

within non-suspended sectors. The system can determine the status of the program operation using the

DQ7 or DQ6 status bits, just as in the standard program operation. See “Write Operation Status” for more

information. The system may also write the autoselect command sequence when the device is in the

Erase Suspend mode. The device allows reading autoselect codes even at addresses within erasing

sectors, since the codes are not stored in the memory array. When the device exits the autoselect mode,

4800 Great America Parkway, Suite 202

10

Santa Clara, CA 95054

Tel: 408-235-8680

Fax: 408-235-8685

Share Link: