HI-507(2005) 查看數據表（PDF） - Intersil

零件编号

产品描述 (功能)

生产厂家

HI-507
(Rev.:2005)

Single 16 and 8/Differential 8-Channel and 4-Channel CMOS Analog Multiplexers

Intersil 

HI-506, HI-507, HI-508, HI-509

Electrical Specifications Supplies = +15V, -15V; VAH (Logic Level High) = 2.4V; VAL (Logic Level Low) = 0.8V,

Unless Otherwise Specified. For Test Conditions, Consult Test Circuits Section (Continued)

PARAMETER

TEST

TEMP

CONDITIONS (°C)

MIN

-2

TYP MAX

-4, -5, -9

MIN

TYP MAX

ANALOG CHANNEL CHARACTERISTICS

Analog Signal Range, VIN

On Resistance, rON

∆rON, (Any Two Channels)

Off Input Leakage Current, IS(OFF)

Note 3

Note 4

Full

-15

-

+15

-15

-

+15

25

-

180

300

-

180

400

25

-

5

-

-

5

-

25

-

0.03

-

-

0.03

-

Full

-

-

50

-

-

50

Off Output Leakage Current,

ID(OFF)

HI-506

Note 4

25

-

0.3

-

-

0.3

-

Full

-

-

300

-

-

300

HI-507

Full

-

-

200

-

-

200

HI-508

Full

-

-

200

-

-

200

HI-509

Full

-

-

100

-

-

100

On Channel Leakage Current, ID(ON)

HI-506

HI-507

HI-508

Note 4

25

-

0.3

-

-

0.3

-

Full

-

-

300

-

-

300

Full

-

-

200

-

-

200

Full

-

-

200

-

-

200

HI-509

Full

-

-

100

-

-

100

Differential Off Output Leakage Current, IDIFF

(HI-507, HI-509 Only)

Full

-

-

50

-

-

50

POWER SUPPLY CHARACTERISTICS

Current, I+

HI-506/HI-507

Note 7

Full

-

1.5

3.0

-

1.5

3.0

HI-508/HI-509

Note 7

Full

-

1.5

2.4

-

1.5

2.4

Current, I-

HI-506/HI-507

Note 7

Full

-

0.4

1.0

-

0.4

1.0

HI-508/HI-509

Note 7

Full

-

0.4

1.0

-

0.4

1.0

Power Dissipation, PD

HI-506/HI-507

Full

-

-

60

-

-

60

HI-508/HI-509

Full

-

-

51

-

-

51

NOTES:

3. VOUT = ±10V, IOUT = +1mA.

4. 10nA is the practical lower limit for high speed measurement in the production test environment.

5. Digital input leakage is primarily due to the clamp diodes (see Schematic). Typical leakage is less than 1nA at 25°C.

6. VEN = 0.8V, RL = 1K, CL = 15pF, VS = 7VRMS, f = 100kHz.

7. VEN, VA = 0V or 2.4V.

UNITS

V

Ω

%

nA

nA

nA

nA

nA

nA

nA

nA

nA

nA

nA

nA

nA

mA

mA

mA

mA

mW

mW

Test Circuits and Waveforms TA = 25°C, VSUPPLY = ±15V, VAH = 2.4V, VAL = 0.8V, Unless Otherwise Specified

1mA

V2

IN

OUT

VIN

V2

rON = 1mA

FIGURE 1A. TEST CIRCUIT

8

FN3142.7

July 21, 2005

Share Link: