HI-508 查看數據表（PDF） - Intersil

零件编号

产品描述 (功能)

生产厂家

HI-508

Single 16 and 8/Differential 8-Channel and 4-Channel CMOS Analog Multiplexers

Intersil 

HI-506, HI-507, HI-508, HI-509

Electrical Specifications Supplies = +15V, -15V; VAH (Logic Level High) = 2.4V; VAL (Logic Level Low) = 0.8V,

Unless Otherwise Specified. For Test Conditions, Consult Test Circuits Section (Continued)

-2

-4, -5, -9

PARAMETER

TEST

TEMP

MIN

CONDITIONS (°C) (Note 11) TYP

MIN

MAX (Note 11) TYP

MAX

Input Leakage Current

(High or Low), IA

ANALOG CHANNEL CHARACTERISTICS

Note 8

Full

-

-

1.0

-

-

1.0

Analog Signal Range, VIN

On Resistance, rON

ΔrON, (Any Two Channels)

Off Input Leakage Current, IS(OFF)

Note 6

Note 7

Full

-15

-

+15

-15

-

+15

25

-

180

300

-

180

400

25

-

5

-

-

5

-

25

-

0.03

-

-

0.03

-

Full

-

-

50

-

-

50

Off Output Leakage Current,

ID(OFF)

HI-506

HI-507

Note 7

25

-

0.3

-

-

0.3

-

Full

-

Full

-

-

300

-

-

200

-

-

300

-

200

HI-508

Full

-

-

200

-

-

200

HI-509

Full

-

-

100

-

-

100

On Channel Leakage Current, ID(ON)

HI-506

Note 7

25

-

0.3

-

-

0.3

-

Full

-

-

300

-

-

300

HI-507

Full

-

-

200

-

-

200

HI-508

HI-509

Differential Off Output Leakage Current, IDIFF

(HI-507, HI-509 Only)

POWER SUPPLY CHARACTERISTICS

Current, I+

HI-506/HI-507

Note 10

HI-508/HI-509

Note 10

Full

-

Full

-

Full

-

-

200

-

-

100

-

-

50

-

-

200

-

100

-

50

Full

-

1.5

3.0

-

1.5

3.0

Full

-

1.5

2.4

-

1.5

2.4

Current, I-

HI-506/HI-507

Note 10

Full

-

0.4

1.0

-

0.4

1.0

HI-508/HI-509

Note 10

Full

-

0.4

1.0

-

0.4

1.0

Power Dissipation, PD

HI-506/HI-507

Full

-

-

60

-

-

60

HI-508/HI-509

Full

-

-

51

-

-

51

NOTES:

6. VOUT = ±10V, IOUT = +1mA.

7. 10nA is the practical lower limit for high speed measurement in the production test environment.

8. Digital input leakage is primarily due to the clamp diodes (see Schematic). Typical leakage is less than 1nA at +25°C.

9. VEN = 0.8V, RL = 1k, CL = 15pF, VS = 7VRMS, f = 100kHz.

10. VEN, VA = 0V or 2.4V.

11. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested.

UNITS

μA

V

Ω

%

nA

nA

nA

nA

nA

nA

nA

nA

nA

nA

nA

nA

nA

mA

mA

mA

mA

mW

mW

9

FN3142.8

October 30, 2007

Share Link: