LT1376 查看數據表（PDF） - Linear Technology
零件编号
产品描述 (功能)
生产厂家
LT1376 Datasheet PDF : 28 Pages
| |||
LT1375/LT1376
ELECTRICAL CHARACTERISTICS The q denotes specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. TJ = 25°C, VIN = 15V, VC = 1.5V, boost open, switch open,
unless otherwise noted.
PARAMETER
Shutdown Thresholds
CONDITIONS
MIN TYP MAX UNITS
VC Open
Device Shutting Down q 0.15 0.37 0.60
V
Device Starting Up q 0.25 0.45 0.60
V
VC Open LT1375HV/LT1376HV Device Shutting Down q 0.15 0.37 0.70
V
LT1375HV/LT1376HV Device Starting Up q 0.25 0.45 0.70
V
Minimum Synchronizing Amplitude (LT1375 Only)
Synchronizing Range (LT1375 Only)
SYNC Pin Input Resistance
VIN = 5V
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: Gain is measured with a VC swing equal to 200mV above the low
clamp level to 200mV below the upper clamp level.
Note 3: Minimum input voltage is not measured directly, but is guaranteed
by other tests. It is defined as the voltage where internal bias lines are still
regulated so that the reference voltage and oscillator frequency remain
constant. Actual minimum input voltage to maintain a regulated output will
depend on output voltage and load current. See Applications Information.
Note 4: This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the internal power switch.
Note 5: Boost current is the current flowing into the BOOST pin with the
pin held 5V above input voltage. It flows only during switch-on time.
Note 6: Input supply current is the bias current drawn by the input pin
when the BIAS pin is held at 5V with switching disabled. Output supply
q
1.5 2.2
V
580
900
kHz
40
kΩ
current is the current drawn by the BIAS pin when the bias pin is held at
5V. Total input referred supply current is calculated by summing input
supply current (ISI) with a fraction of output supply current (ISO):
ITOT = ISI + (ISO)(VOUT/VIN)(1.15)
With VIN = 15V, VOUT = 5V, ISI = 0.9mA, ISO = 3.6mA, ITOT = 2.28mA.
For the LT1375, quiescent current is equal to:
ITOT = ISI + ISO(1.15)
because the BIAS pin is internally connected to VIN.
Note 7: Switch-on resistance is calculated by dividing VIN to VSW voltage
by the forced current (1.5A). See Typical Performance Characteristics for
the graph of switch voltage at other currents.
Note 8: Transconductance and voltage gain refer to the internal amplifier
exclusive of the voltage divider. To calculate gain and transconductance
refer to sense pin on fixed voltage parts. Divide values shown by the ratio
VOUT/2.42.
TYPICAL PERFORMANCE CHARACTERISTICS
Inductor Core Loss
1.0
20
VOUT = 5V, VIN = 10V, IOUT = 1A
12
8
TYPE 52
4
0.1
POWDERED IRON 2
Kool Mµ®
1.2
0.8
PERMALLOY
0.01
CORE LOSS IS
µ = 125
INDEPENDENT OF LOAD
CURRENT UNTIL LOAD CURRENT FALLS
LOW ENOUGH FOR CIRCUIT TO GO INTO
DISCONTINUOUS MODE
0.001
0
5
10
15
20
INDUCTANCE (µH)
0.4
0.2
0.12
0.08
0.04
0.02
25
1375/76 G01
Switch Peak Current Limit
2.5
TYPICAL
2.0
GUARANTEED MINIMUM
1.5
1.0
0.5
Feedback Pin Voltage and Current
2.44
2.0
2.43
1.5
VOLTAGE
2.42
1.0
CURRENT
2.41
0.5
0
2.40
0
0
20
40
60
80 100
–50 –25 0 25 50 75 100 125
DUTY CYCLE (%)
JUNCTION TEMPERATURE (°C)
1375/76 G08
1375/76 G09
Kool Mµ is a registered trademark of Magnetics, Inc.
4
Share Link: 