DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

LTC1703I 查看數據表(PDF) - Linear Technology

零件编号
产品描述 (功能)
生产厂家
LTC1703I Datasheet PDF : 36 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
LTC1703
APPLICATIO S I FOR ATIO
of the equation—with a typical value on the order of 1µH,
the inductor allows very fast di/dt slew rates. The result is
superior transient response compared with conventional
solutions.
High Efficiency
The LTC1703 uses a synchronous step-down (buck)
architecture, with two external N-channel MOSFETs per
output. A floating topside driver and a simple external
charge pump provide full gate drive to the upper MOSFET.
The voltage mode feedback loop and MOSFET VDS current
limit sensing remove the need for an external current
sense resistor, eliminating an external component and a
source of power loss in the high current path. Properly
designed circuits using low gate charge MOSFETs are
capable of efficiencies exceeding 90% over a wide range
of output voltages.
VID Programming
The LTC1703 includes an onboard feedback network that
programs the output voltage at side 1 in accordance with
the Intel Mobile VID specification (Table 1). The network
includes a 10k resistor (R11) connected from SENSE to
FB1, and a variable value resistor (RB1) from FB1 to SGND,
with the value set by the digital code present at the VID0:4
pins. SENSE should be connected to VOUT1 to allow the
network to monitor the output voltage. No additional
feedback components are required to set the output volt-
age at controller 1, although loop compensation compo-
nents are still required. Each VIDn pin includes an internal
40k pull-up resistor, allowing it to float high if left uncon-
nected. The pull-up resistors are connected to VCC through
diodes (see Block Diagram), allowing the VIDn pins to be
pulled above VCC without damage.
Note that codes 01111 and 11111, defined by Intel to
indicate “no CPU present,” do generate output voltages at
VOUT1 (1.25V and 0.9V, respectively). Note also that
controller 2 on the LTC1703 is not connected to the VID
circuitry, and works independently from controller 1.
ARCHITECTURE DETAILS
The LTC1703 dual switching regulator controller includes
two independent regulator channels. The two sides of the
10
chip and their corresponding external components act
independently of each other with the exception of the
common input bypass capacitor, the VID circuitry at side
1, and the FCB and FAULT pins, which affect both chan-
nels. In the following discussions, when a pin is referred
to without mentioning which side is involved, that discus-
sion applies equally to both sides.
Switching Architecture
Each half of the LTC1703 is designed to operate as a
synchronous buck converter (Figure 1). Each channel
includes two high power MOSFET gate drivers to control
external N-channel MOSFETs QT and QB. These drivers
have 0.5output impedances and can carry well over an
amp of continuous current with peak currents up to 5A to
slew large MOSFET gates quickly. The external MOSFETs
are connected with the drain of QT attached to the input
supply and the source of QT at the switching node SW. QB
is the synchronous rectifier with its drain at SW and its
source at PGND. SW is connected to one end of the
inductor, with the other end connected to VOUT. The output
capacitor is connected from VOUT to PGND.
When a switching cycle begins, QB is turned off and QT is
turned on. SW rises almost immediately to VIN and the
inductor current begins to increase. When the PWM pulse
finishes, QT turns off and one nonoverlap interval later, QB
turns on. Now SW drops to PGND and the inductor current
decreases. The cycle repeats with the next tick of the
master clock. The percentage of time spent in each mode
is controlled by the duty cycle of the PWM signal, which in
turn is controlled by the feedback amplifier. The master
clock runs at a 550kHz rate and turns QT once every 1.8µs.
In a typical application with a 5V input and a 1.5V output,
the duty cycle will be set at 1.5/5 × 100% or 30% by the
feedback loop. This will give roughly a 540ns on-time for
QT and a 1.26µs on-time for QB.
VIN
TG
LTC1703 SW
PGND BG
QT LEXT
QB
+
CIN
VOUT
+
COUT
1703 F01
Figure 1. Synchronous Buck Architecture
1703fa

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]