LTC2953IDD-2-TRPBF 查看數據表（PDF） - Linear Technology
零件编号
产品描述 (功能)
生产厂家
LTC2953IDD-2-TRPBF Datasheet PDF : 20 Pages
| |||
LTC2953
PIN FUNCTIONS
GND (Pin 1): Ground.
VM (Pin 2): Voltage Monitor Input. Input to an accurate
comparator with a 0.5V threshold. VM controls the state
of the ⎯R⎯S⎯T output pin and is independent of ⎯P⎯B, ⎯P⎯F⎯I and
UVLO status. A voltage below 0.5V on this pin asserts
⎯R⎯S⎯T low. Connect to GND if unused.
⎯K⎯I⎯L⎯L (Pin 3): ⎯K⎯I⎯L⎯L Input. Forcing ⎯K⎯I⎯L⎯L low releases the
enable output. During system turn on, this pin is blanked
by a 512ms internal timer (tKILL, ON BLANK) to allow the
system to pull ⎯K⎯I⎯L⎯L high. This pin has an accurate 0.6V
threshold and can be used as a power kill voltage monitor.
Set the pin voltage above its threshold if unused.
PDT (Pin 4): Power Down Time Input. A capacitor to
ground determines the additional time (6.4 seconds/μF)
that ⎯P⎯B or UVLO must be held low before releasing the
EN/⎯E⎯N and ⎯I⎯N⎯T outputs. If this pin is left open, the power
down delay time defaults to 64ms.
⎯P⎯B (Pin 5): Push Button Input. Connecting ⎯P⎯B to ground
through a momentary switch provides On/Off control via the
EN/⎯E⎯N and ⎯I⎯N⎯T outputs. An internal 100k pull-up resistor
connects to an internal 1.9V bias voltage. The rugged ⎯P⎯B
input withstands ±10kV ESD HBM and can be pulled up to
27V externally without consuming extra current. Voltages
below ground will not damage the pin.
VIN (Pin 6): Power Supply Input: 2.7V to 27V.
UVLO (Pin 7): UVLO Comparator Input. When UVLO drops
below its falling threshold (0.5V) for more than 32ms, the
LTC2953 asserts ⎯I⎯N⎯T low, thereby requesting a system
power down. If UVLO remains below its falling threshold
(0.5V) for longer than the adjustable power down delay,
the enable output is released. Additionally, UVLO provides
a ⎯P⎯B lock out feature that prevents the user from asserting
the enable output when UVLO falls below its threshold.
Connect to VIN if unused.
PFI (Pin 8): Power Fail Comparator Input. Input to an ac-
curate comparator with a 0.5V falling threshold and 4mV
of hysteresis. PFI controls the state of the ⎯P⎯F⎯O output pin
and is independent of ⎯P⎯B, VM and UVLO status. Connect
to GND if unused.
⎯P⎯F⎯O (Pin 9): Power Fail Output. This pin is a high voltage
open drain pull-down. ⎯P⎯F⎯O pulls low when PFI is below
0.5V. Open circuit when unused.
⎯R⎯S⎯T (Pin 10): Reset Output. This pin is an open drain
pull-down. Pulls low when VM input is below 0.5V and is
held low for 200ms after VM input is above 0.5V. Open
circuit when unused.
EN (LTC2953-1, Pin 11): Open Drain Enable Output. This
output is intended to enable system power. EN is asserted
high after a valid ⎯P⎯B turn on event (tDB, ON). EN is released
low if: a) ⎯K⎯I⎯L⎯L is not driven high (by μP) within 512ms of
the initial valid ⎯P⎯B power turn on event, b) ⎯K⎯I⎯L⎯L is driven
low during normal operation, c) P⎯ B⎯ or UVLO is asserted and
held low (t > tPD, Min + tPDT) during normal operation.
⎯E⎯N (LTC2953-2, Pin 11): Open Drain Enable Output. This
output is intended to enable system power. ⎯E⎯N is asserted
low after a valid ⎯P⎯B turn on event (tDB, ON). ⎯E⎯N is released
high if: a) ⎯K⎯I⎯L⎯L is not driven high (by μP) within 512ms of
the initial valid ⎯P⎯B power turn-on event, b) ⎯K⎯I⎯L⎯L is driven
low during normal operation, c) P⎯ B⎯ or UVLO is asserted and
held low (t > tPD, Min + tPDT) during normal operation.
⎯I⎯N⎯T (Pin 12): Open Drain Interrupt Output. After a turn off
event is detected (tDB, OFF) from ⎯P⎯B or UVLO, the LTC2953
interrupts the system (μP) by asserting ⎯I⎯N⎯T low. The μP
would perform power down and housekeeping tasks and
then assert the ⎯K⎯I⎯L⎯L pin low, thus releasing the enable out-
put. The ⎯I⎯N⎯T pulse width is a minimum of 32ms and stays
low as long as ⎯P⎯B is asserted. If ⎯P⎯B is asserted for longer
than tPD, Min + tPDT, however, the ⎯I⎯N⎯T and EN/⎯E⎯N outputs
are immediately released. Open circuit when unused.
Exposed Pad (Pin 13): Exposed Pad may be left open or
connected to ground.
2953f
7
Share Link: 