M61323FP 查看數據表（PDF） - MITSUBISHI ELECTRIC

零件编号

产品描述 (功能)

生产厂家

M61323FP

WIDE FREQUENCY BAND ANALOG SWITCH

MITSUBISHI ELECTRIC  

MITSUBISHI ICs <Monitor>

M61323SP/FP

WIDE FREQUENCY BAND ANALOG SWITCH

<HV-SW>

Hi level output voltage 1,2 / Lo level output voltage 1,2

1. The conditions is as table. Input SG8 to Pin7 (or Pin8 ). Set SW13 to GND, read the output High level and

low voltage of TP19, TP18. The value is as Vdch1, Vdcl1.

2. Input SG8 to Pin15 (or Pin16 ). Set SW13 to OPEN, read the output High level and low voltage of TP19, TP18.

The value is as Vdch2, Vdcl2.

Input threshold voltage H / Input threshold voltage L

1. Set SW13 to GND (or OPEN). Gradually increasing the voltage of Pin7 (or Pin15 ) from 0V, measure the input

voltage of Pin7 (or Pin15 ) when the TP19 voltage turned high level (3.8V or more). The value is as VithH.

2. Gradually decreasing the voltage of Pin7 (or Pin15 ) from 3V, measure the input voltage of Pin7 (or Pin15 )

when the TP19 voltage turned low level (0.5V or less). The value is as VithL.

3. In the same way, measure the input voltage of Pin8 (or Pin16 ) as VithH, VithL.

Rising time / Falling time

100%

1. The conditions is as table. This measurement shall use active probe.

80%

2. Measure rising Tri and falling Tfi for 20%~80% of the

output pulse as Tr3, Tf3 (Tr4, Tf4 ) .

Rising delay time / Falling delay time

0%

Tr'

Set SW13 to GND (or OPEN), input SG8 to Pin7 (or Pin15 ).

Measure the rising delay time HVdr and the falling delay time HVdf. SG8

20%

Tf'

In the same way, measure HVdr and HVdf

50%

when input SG8 to Pin8 (or Pin16 ).

HVDr

HVDf

<Sync-Separation>

Waveform output

50%

Sync input minimum voltage

Gradually decreasing the amplitude of SG7 in Pin22, measure the amplitude of SG7 when the Sync-Sep output

signal turn off . The value is as SYrv.

Sync output High level voltage / Sync output Low level voltage

Input SG7 to Pin22, read the output High level and low voltage of TP21. The value is as SYVH, SYVL.

Sync output rising time / Sync output falling time

1. The conditions is as table. (SG7 amplitude 0.3Vp-p)

This measurement shall use active probe.

100%

90%

2. Measure rising Tri and falling Tfi for 10%~90%

of the input pulse as STr, STf .

Sync output rising delay time

Sync output falling delay time

0%

STr

SG7

10%

STf

Input SG7 to Pin22. Measure the rising delay time Sdr

50%

and the falling delay time Sdf.

SDr

SDf

Waveform output

50%

<Others>

Channel select SW threshold 1,2

1. Gradually increasing the voltage of Pin13 from 0V, measure the maximum voltage of Pin13 when the channel 1

is selected. The value is as Vthch1.

2.Gradually decreasing the voltage of Pin13 from 5V, measure the minimum voltage of Pin13 when the channel 2

is selected. The value is as Vthch2.

Power save SW threshold 1,2

1. Gradually increasing the voltage of Pin11 from 0V, measure the maximum voltage of Pin11 when the Power save

mode . The value is as VthPL.

2.Gradually decreasing the voltage of Pin13 from 5V, measure the minimum voltage of Pin11 when the Power save

mode . The value is as VthPH.

MITSUBISHI

8 15

Share Link: