BMP-5/5-3.3/4-D24 查看數據表（PDF） - DATEL Data Acquisition products

零件编号

产品描述 (功能)

生产厂家

BMP-5/5-3.3/4-D24

Dual Output BMP Models 5V and 3.3V, 2" x 3" 35 Watt, DC/DC Converters

DATEL Data Acquisition products  

XMP Series

35W, DUAL OUTPUT DC/DC CONVERTERS

On/Off Control (Standard)

The On/Off Control pin (pin 5) may be used for remote on/off operation. As

shown in Figure 6, the control pin has an internal 10kΩ pull-up resistor to

approximately 10V. The converter is designed so that it is enabled when the

control pin is left open (normal mode) and disabled when the control pin is

pulled low (to less than +1.2V relative to –Input, pin 2).

Dynamic control of the on/off function is best accomplished with a mechani-

cal relay or an open-collector/open-drain drive circuit (optically isolated if

appropriate). The drive circuit should obviously be able to sink approximately

1.5mA when activated and withstand more than 10 Volts when deactivated.

Applying an external voltage to pin 5 when no input power is applied to the

converter can cause permanent damage to the converter. The on/off control

function, however, is designed such that the converter can be disabled (pin

5 pulled low) while input power is ramping up and then "released" once the

input has stabilized. Under these circumstances, it takes approximately 30ms

for the output of the fully loaded DC/DC to ramp up and settle to within ±1%

of its final value after the converter has been turned on.

Synchronization (Optional)

In critical applications employing multiple switching DC/DC converters, it may

be desirable to intentionally synchronize the switching of selected converters

(so the system noise can be reduced with notch filtering) or to purposely

desynchronize the converters (to lessen the current-carrying requirements on

intermediate dc buses). BMP DC/DC Converters have been designed so that

the On/Off Control function on pin 5 can be replaced with a Sync function.

This change has to be implemented by DATEL during the product assembly

process. Contact our Applications Engineering Group for additional details.

To synchronize the switching of multiple BMP converters configured with the

Sync function, an external clock can be applied to pin 5 of each converter.

The clock should be a TTL square wave referenced to –Input (logic high =

+2 to +5 Volts, 250µA max.; logic low = 0 to +0.8 Volts, 70µA max.) with a

maximum 1µsec "high" duration. The frequency of the synchronizing clock

should be higher than that of any individual converter.

Output Trimming

The total output voltage span of the 5 Volt output, from +5V Output (pin 9)

to Output Return (pin 8) may be trimmed ±5% via a single trimpot or fixed

resistor. The trimpot should be connected as shown in Figure 3 with its wiper

connected to pin 10 (Trim). A trimpot can also be used to determine the value

of a single fixed resistor which can be connected between pin 10 (Trim) and

pin 9 (+5V Output) to trim "down" the output voltages, or between pins 10

(Trim) and 8 (Output Return) to trim "up" the output voltages. Fixed resistors

should have absolute TCR's less than 100ppm/°C to ensure stability.

Case Connection

Unlike most other DC/DC converters, BMP DC/DC's do not have their metal

case connected to one of their input pins. The "uncommitted" case is con-

nected to pin 4 which, depending on your system configuration, should be

connected to either +Input (pin 3) or –Input (pin 2).

3

+INPUT

+10V

10k9

5

ON/OFF

CONTROL

2

–INPUT

Figure 2. Driving the On/Off Control Pin

3 +INPUT

2

–INPUT

7

+3.3V OUTPUT

OUTPUT 8

RETURN

TRIM

10

+5V OUTPUT

9

+3.3V LOAD

20kΩ

5-22

Turns

+5V LOAD

Figure 3. +5VOUT Trim Connections Using A Trim Pot

3 +INPUT

2

–INPUT

7

+3.3V OUTPUT

OUTPUT 8

RETURN

TRIM

RTRIM DOWN

10

+5V OUTPUT

9

+3.3V LOAD

+5V LOAD

RTDOWN (kΩ) =

2.49(VO – 2.53)

5 – VO

–16.2

Figure 4. +5VOUT Trim Down Connections Using A Fixed Resistor

3 +INPUT

2

–INPUT

7

+3.3V OUTPUT

OUTPUT 8

RETURN

TRIM

10

RTRIM UP

+5V OUTPUT

9

+3.3V LOAD

+5V LOAD

6.30

RT UP (kΩ) = VO – 5

–16.2

Figure 5. +5VOUT Trim Up Connections Using A Fixed Resistor

Note: Resistor values are in kΩ. Accuracy of adjustment is subject to

tolerances of resistors and factory-adjusted output accuracy.

VO = desired output voltage.

4

Share Link: