MAAPSS0096 查看數據表（PDF） - Tyco Electronics
零件编号
产品描述 (功能)
生产厂家
MAAPSS0096 Datasheet PDF : 6 Pages
| |||
1 Watt Power Amplifier
4.9 - 6.0 GHz
RoHS
Compliant
MAAPSS0096
V1
Electrical Specifications: TC = 40 °C, VDD = 7.0 V, VGG = -1.8 V, Z0 = 50 Ω
Parameter
Test Conditions
Units
Min.
Typ.
Max.
Input VSWR
F = 5.825 GHz, PIN = +14 dBm
—
—
1.5:1
2.0:1
Gain
F = 5.825 GHz, PIN = 0 dBm
dB
18.0
20.5
—
P1dB
F = 5.825 GHz
dBm
—
29.5
—
Saturated Power
F = 5.825 GHz, PIN = +14 dBm
dBm
29.2
31.5
—
Drain Current at Psat
2nd Harmonics
3rd Harmonics
Thermal resistance 3
F = 5.825 GHz, PIN = +14 dBm
Output Power = 29.5 dBm
2nd Stage Only
mA
—
500
600
dBc
—
-40
—
dBc
—
-70
—
°C/W
—
31
—
Third-Order Intercept Point
Stability
Noise Figure
+3 V < VDD < +10 V, PIN< +14 dBm, VSWR < 6:1,
-25 ºC < TC < 85 ºC, RBW = 3 MHz (max. hold)
F = 5.825 GHz
dBm
—
dB
—
40
—
All spurs < -70 dBc
—
5.3
—
3. When using the thermal resistance, you must use the power dissipated by the second stage only (not the total power dissipated). The
second stage dissipates 80% of the total power.
Recommended Operating Conditions 4,5
Characteristic Symbol Unit Min. Typ. Max.
Drain Voltage
VDD
V
4.5 7.0 8.0
Gate Voltage 5
VGG
V
-2.5 -1.8 -1.0
Input Power
PIN
dBm
—
15
Gate Current
IGG
mA
-4
1
+4
Case Temperature TC
°C
-40
25
85
4. Operation outside of these ranges may reduce product
reliability.
5. A 100-ohm resistor should be used in the gate voltage line.
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
Absolute Maximum Ratings 6,7
Parameter
Input Power (4.9 - 6.0 GHz)
Operating Voltages
Operating Temperature
Channel Temperature
Storage Temperature
Absolute Maximum
+ 15 dBm
+10 volts
-40 °C to +70 °C
+150 °C
-40 °C to +150 °C
6. Exceeding any one or combination of these limits may cause
permanent damage to this device.
7. M/A-COM does not recommend sustained operation near
these survivability limits.
Operating The MAAPSS0096
To operate the device, follow these steps.
1. Apply VGG = -1.8 V, VDD= 0 V.
2. Ramp VDD to desired voltage, typically 5 to 7 V.
3. Adjust VGG to set IDQ, (approximately –1.8 V).
4. Set RF input.
5. Power down in reverse sequence . Turn gate voltage
off last.
2
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
• North America Tel: 800.366.2266 / Fax: 978.366.2266
• Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
• Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macom.com for additional data sheets and product information.
Share Link: 