MC100E241
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC
PECL Mode Power Supply
VEE
NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
Iout
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI v VCC
VI w VEE
8
V
−8
V
6
V
−6
V
50
mA
100
mA
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
PLCC−28
PLCC−28
0 to +85
−65 to +150
63.5
43.5
°C
°C
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case)
Standard Board
Tsol
Wave Solder
Pb
Pb−Free
PLCC−28
22 to 26
265
265
°C/W
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. 100E SERIES PECL DC CHARACTERISTICS VCCx = 5.0 V, VEE = 0.0 V (Note 1)
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
125 150
125 150
144 173 mA
VOH
Output HIGH Voltage (Note 2)
3975 4050 4120 3975 4050 4120 3975 4050 4120 mV
VOL
Output LOW Voltage (Note 2)
3190 3295 3380 3190 3255 3380 3190 3260 3380 mV
VIH
Input HIGH Voltage
3835 3975 4120 3835 3975 4120 3835 3975 4120 mV
VIL
Input LOW Voltage
3190 3355 3525 3190 3355 3525 3190 3355 3525 mV
IIH
Input HIGH Current
150
150
150 mA
IIL
Input LOW Current
0.5 0.3
0.5 0.25
0.5 0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.8 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
Table 5. 100E SERIES NECL DC CHARACTERISTICS VCCx = 0.0 V; VEE = −5.0 V (Note 3)
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
125 150
125 150
144 173 mA
VOH
Output HIGH Voltage
−1025 −950 −880 −1025 −950 −880 −1025 −950 −880 mV
VOL
Output LOW Voltage
−1810 −1705 −1620 −1810 −1745 −1620 −1810 −1740 −1620 mV
VIH
Input HIGH Voltage (Single−Ended)
−1165 −1025 −880 −1165 −1025 −880 −1165 −1025 −880 mV
VIL
Input LOW Voltage (Single−Ended)
−1810 −1645 −1475 −1810 −1645 −1475 −1810 −1645 −1475 mV
IIH
Input HIGH Current
150
150
150 mA
IIL
Input LOW Current
0.5 0.3
0.5 0.25
0.5 0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
3. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.8 V.
4. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
http://onsemi.com
3