MC100EL58DG(2016) 查看數據表（PDF） - ON Semiconductor
零件编号
产品描述 (功能)
生产厂家
MC100EL58DG Datasheet PDF : 8 Pages
| |||
MC10EL58, MC100EL58
Table 8. 100EL SERIES NECL DC CHARACTERISTICS (VCC= 0.0 V; VEE= −5.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
VOL
Output LOW Voltage (Note 2)
VIH
Input HIGH Voltage
VIL
Input LOW Voltage
IIH
Input HIGH Current
IIL
Input LOW Current
14
17
14
17
16
19
mA
−1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
−1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
−1165
−880 −1165
−880 −1165
−880 mV
−1810
−1475 −1810
−1475 −1810
−1475 mV
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
2. Outputs are terminated through a 50 ohm resistor to VCC−2 volts.
Table 9. AC CHARACTERISTICS (VCC= 5.0 V; VEE= 0.0 V or VCC= 0.0 V; VEE= −5.0 V (Note 1))
Symbol
Characteristic
−40°C
25°C
85°C
Min Typ Max Min Typ Max Min Typ Max Unit
fmax Maximum Toggle Frequency
1.5
GHz
tPLH
Propagation Delay to Output
tPHL
D to Q
SEL to Q
ps
60 220 380 120 230 340 140 250 360
90 250 410 150 260 370 170 280 390
tJITTER Random Clock Jitter (RMS)
0.9
ps
tr
Output Rise/Fall Times Q
tf
(20% − 80%)
100 225 350 100 225 350 100 225 350 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. 10 Series: VEE can vary +0.06 V / −0.5 V.
100 Series: VEE can vary +0.8 V / −0.5 V.
Q
Driver
Device
Q
Zo = 50 W
Zo = 50 W
50 W
50 W
D
Receiver
Device
D
VTT
VTT = VCC − 3.0 V
Figure 2. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D − Termination of ECL Logic Devices.)
www.onsemi.com
5
Share Link: 