MC100EL58DR2 查看數據表（PDF） - ON Semiconductor
零件编号
产品描述 (功能)
生产厂家
MC100EL58DR2 Datasheet PDF : 9 Pages
| |||
MC10EL58, MC100EL58
Table 8. 100EL SERIES NECL DC CHARACTERISTICS VCC= 0.0 V; VEE= −5.0 V (Note 8)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
14
17
14
17
16
19
mA
VOH
Output HIGH Voltage (Note 9)
−1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
VOL
Output LOW Voltage (Note 9)
−1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
VIH
Input HIGH Voltage
−1165
−880 −1165
−880 −1165
−880 mV
VIL
Input LOW Voltage
−1810
−1475 −1810
−1475 −1810
−1475 mV
IIH
Input HIGH Current
150
150
150 mA
IIL
Input LOW Current
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
8. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
9. Outputs are terminated through a 50 ohm resistor to VCC−2 volts.
Table 9. AC CHARACTERISTICS VCC= 5.0 V; VEE= 0.0 V or VCC= 0.0 V; VEE= −5.0 V (Note 10)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
fmax
Maximum Toggle Frequency
1.5
GHz
tPLH
Propagation Delay to Output
ps
tPHL
D to Q
60 220 380 120 230 340 140 250 360
SEL to Q
90 250 410 150 260 370 170 280 390
tJITTER
Random Clock Jitter (RMS)
0.9
ps
tr
Output Rise/Fall Times Q
tf
(20% − 80%)
100 225 350 100 225 350 100 225 350 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
10. 10 Series: VEE can vary +0.06 V / −0.5 V.
100 Series: VEE can vary +0.8 V / −0.5 V.
Q
Driver
Device
Q
Zo = 50 W
Zo = 50 W
50 W
50 W
D
Receiver
Device
D
VTT
VTT = VCC − 3.0 V
Figure 2. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D − Termination of ECL Logic Devices.)
http://onsemi.com
5
Share Link: 