MC100LVE310(2016) 查看數據表（PDF） - ON Semiconductor
零件编号
产品描述 (功能)
生产厂家
MC100LVE310 Datasheet PDF : 7 Pages
| |||
MC100LVE310
Table 6. LVNECL DC CHARACTERISTICS (VCC = 5.0 V, VEE = −3.3 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
VOH Output HIGH Voltage (Note 2)
VOL
Output LOW Voltage (Note 2)
VIH
Input HIGH Voltage
(Single-Ended)
55
60
55
60
65
70 mA
−1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
−1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
−1165
−880 −1165
−880 −1165
−880 mV
VIL
Input LOW Voltage
(Single-Ended)
−1810
−1475 −1810
−1475 −1810
−1475 mV
VBB
VIHCMR
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
−1.38
−1.5
−1.26 −1.38
−0.4 −1.5
−1.26 −1.38
−0.4 −1.5
−1.26 V
−0.4 V
IIH
Input HIGH Current
IIL
Input LOW Current
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary ± 0.3 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2 V.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. VIHCMR is defined as the range within which the VIH level may vary, with the device
still meeting the propagation delay specification. The VIL level must be such that the peak to peak voltage is less than 1.0 V and greater than
or equal to VPP(min).
Table 7. AC CHARACTERISTICS (VCC = 3.3 V; VEE = 0.0 V or VCC = 0.0 V; VEE = −3.3 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
fmax Maximum Toggle Frequency
@ Vout > 500 mVpp
tPLH Propagation Delay to Output
tPHL
IN (Differential Configuration) (Note 2)
IN (Single-Ended) (Note 3)
0.5 1.0
0.5 1.0
0.5 1.0
GHz
ps
525
725 550
750 575
775
500
750 550
800 600
850
tskew Within-Device Skew (Note 4)
75
50
50 ps
Part-to-Part Skew (Differential Configuration)
250
200
200
tJITTER
VPP
tr/tf
Additive CLOCK Jitter (RMS) < 0.5 GHz
Input Swing (Note5)
Output Rise/Fall Time (20%−80%)
1.5 2.0
1.5 2.0
1.5 2.0 ps
500
1000 500
1000 500
1000 mV
200
600 200
600 200
600 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. VEE can vary ± 0.3 V.
2. The differential propagation delay is defined as the delay from the crossing points of the differential input signals to the crossing point of the
differential output signals.
3. The single-ended propagation delay is defined as the delay from the 50% point of the input signal to the 50% point of the output signal.
4. The within-device skew is defined as the worst case difference between any two similar delay paths within a single device.
5. VPP(min) is defined as the minimum input differential voltage which will cause no increase in the propagation delay. The VPP(min) is AC limited
for the LVE310 as a differential input as low as 50 mV will still produce full ECL levels at the output.
www.onsemi.com
4
Share Link: 