826D9 查看數據表（PDF） - Micrel

零件编号

产品描述 (功能)

生产厂家

826D9

Quad Output PMIC with HyperLight Load™ DC-DC, three LDOs, and I2C Control

Micrel 

MIC2826

Quad Output PMIC with HyperLight Load™ DC-

DC, three LDOs, and I2C Control

General Description

The Micrel MIC2826 is a four output, programmable Power

Management IC, optimized for high efficiency power

support in Mobile Application Processors, Co-Processors,

DSPs, GPS and Media Player chipsets. The device

integrates a single 500mA PWM/PFM synchronous buck

(step-down) regulator with three Low Dropout Regulators

and a 400kHz I²C interface that provides programmable

Dynamic Voltage Scaling (DVS), Power Sequencing, and

individual output Enable/Disable controls allowing the user

to optimally control all four outputs.

The 4MHz synchronous buck regulator features a patented

HyperLight Load™ (HLL) architecture which minimizes

switching losses and provides low quiescent current

operation for high efficiency at light loads. Additional

benefits of this proprietary architecture are low output

ripple voltage and fast transient response throughout the

entire load range with the use of small output capacitors,

reducing the overall system size.

Three high performance LDOs are integrated into the

MIC2826 to provide additional system voltages for I/O,

memory and other analog functions. Each LDO is capable

of sourcing 150mA output current with high PSRR and low

output noise. A 2% output voltage accuracy, low dropout

voltage (150mV @ 150mA), and low ground current of

116µA (all three LDOs operating) makes this device ideally

suited for mobile applications.

The MIC2826 is available in a tiny 14-pin 2.5mm x 2.5mm

Thin MLF® with a junction operating range from -40°C to

+125°C.

Data sheets and support documentation can be found on

Micrel’s web site at: www.micrel.com.

Applications

• Application processors

• GPS subsystems

• General purpose PMIC

• Mobile phones / PDAs

• Portable media players

• Mobile television receivers

Features

• Fast-mode I2C control interface

• Tiny 14-pin 2.5mm x 2.5mm MLF® package

• Default start-up voltage states and sequencing

• Fault indication processor flag - IRQb

• -40°C to 125°C junction temperature range

• Thermal shutdown and current-limit protection

• Power On After Fault (POAF) function

DC-DC Synchronous Buck

• 2.7V to 5.5V input voltage range

• 500mA continuous output current

• HyperLight Load™ mode

– 25µA quiescent current

• 90% peak efficiency; 85% at 1mA

• Ultra-fast transient response

• Dynamic Voltage Scaling (DVS) range: 0.8V to 1.8V

– 0.8V to 1.2V in 25mV steps

– 1.2V to 1.8V in 50mV steps

• ±2% initial accuracy

• Low output voltage ripple: 20mVpp in HyperLight

Load™ mode, 3mV in full PWM mode

LDOs

• 1.8V to VDVIN input voltage range

• 150mA output current (each LDO)

• Dynamic Voltage Scaling (each LDO)

– DVS range: 0.8V to 3.3V in 50mV steps

• ±2% initial accuracy

• Low quiescent current – 50µA (each LDO)

• Low dropout voltage – 50mV @ 50mA

• Low output noise - 45µVRMS

• Stable with ceramic output capacitors

• 65dB PSRR at 1kHz

HyperLight Load is a trademark of Micrel, Inc

MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.

Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com

July 2009

M9999-071609-A

Share Link: