CY7C1334 查看數據表（PDF） - Cypress Semiconductor
零件编号
产品描述 (功能)
生产厂家
CY7C1334 Datasheet PDF : 12 Pages
| |||
CY7C1334
Pin Definitions
Pin Number
49−44,
81–82, 99,
100, 32–37
96–93
Name
A[15:0]
BWS[3:0]
88
WE
85
ADV/LD
89
CLK
98
CE1
97
CE2
92
CE3
86
OE
87
CEN
29–28,
25–22,
19–18,
13–12, 9–6,
3–2, 79–78,
75–72,
69–68, 63–62
59–56, 53–52
DQ[31:0]
31
Mode
15, 16, 41, 65, VDD
66, 91
17, 40, 67, 90
4, 11, 14, 20,
27, 54, 61, 70,
77
VSS
VDDQ
5, 10, 21, 26, VSSQ
55, 60, 71, 76
64
NC
I/O
Input-
Synchronous
Description
Address Inputs used to select one of the 65,536 address locations. Sampled at the
rising edge of the CLK.
Input-
Synchronous
Input-
Synchronous
Byte Write Select Inputs, active LOW. Qualified with WE to conduct writes to the
SRAM. Sampled on the rising edge of CLK. BWS0 controls DQ[7:0], BWS1 controls
DQ[15:8], BWS2 controls DQ[23:16], BWS0 controls DQ[31:24].
Write Enable Input, active LOW. Sampled on the rising edge of CLK if CEN is active
LOW. This signal must be asserted LOW to initiate a write sequence.
Input-
Synchronous
Advance/Load input used to advance the on-chip address counter or load a new
address. When HIGH (and CEN is asserted LOW) the internal burst counter is
advanced. When LOW, a new address can be loaded into the device for an access.
After being deselected, ADV/LD should be driven LOW in order to load a new
address.
Input-Clock Clock input. Used to capture all synchronous inputs to the device. CLK is qualified
with CEN. CLK is only recognized if CEN is active LOW.
Input-
Synchronous
Input-
Synchronous
Input-
Synchronous
Input-
Asynchronous
Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in
conjunction with CE2 and CE3 to select/deselect the device.
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in
conjunction with CE1 and CE3 to select/deselect the device.
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in
conjunction with CE1 and CE2 to select/deselect the device.
Output Enable, active LOW. Combined with the synchronous logic block inside the
device to control the direction of the I/O pins. When LOW, the I/O pins are allowed
to behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act
as input data pins. OE is masked during the data portion of a write sequence,
during the first clock when emerging from a deselected state, and when the device
has been deselected.
Input-
Synchronous
Clock Enable Input, active LOW. When asserted LOW the clock signal is recog-
nized by the SRAM. When deasserted HIGH the clock signal is masked. Since the
deasserting CEN does not deselect the device, CEN can be used to extend the
previous cycle when required.
I/O-
Synchronous
Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that
is triggered by the rising edge of CLK. As outputs, they deliver the data contained
in the memory location specified by A[15:0] during the previous clock rise of the
read cycle. The direction of the pins is controlled by OE and the internal control
logic. When OE is asserted LOW, the pins can behave as outputs. When HIGH,
DQ[31:0] are placed in a three-state condition. The outputs are automatically
three-stated during the data portion of a write sequence, during the first clock when
emerging from a deselected state, and when the device is deselected, regardless
of the state of OE.
Input
Strap Pin
Mode Input. Selects the burst order of the device. Tied HIGH selects the interleaved
burst order. Pulled LOW selects the linear burst order. Mode should not change
states during operation. When left floating Mode will default HIGH, to an interleaved
burst order.
Power Supply Power supply inputs to the core of the device. Should be connected to 3.3V power
supply.
Ground Ground for the core of the device. Should be connected to ground of the system.
I/O Power Power supply for the I/O circuitry. Should be connected to a 3.3V power supply.
Supply
I/O Ground Ground for the I/O circuitry. Should be connected to ground of the system.
-
No Connect. Reserved for drive strength control input.
Document #: 38-05065 Rev. **
Page 3 of 12
Share Link: 