NCP5104(2008) 查看數據表（PDF） - ON Semiconductor
零件编号
产品描述 (功能)
生产厂家
NCP5104 Datasheet PDF : 15 Pages
| |||
NCP5104
ELECTRICAL CHARACTERISTIC (VCC = Vboot = 15 V, VGND = Vbridge, -40°C < TJ < 125°C, Outputs loaded with 1 nF)
TJ -40°C to 125°C
Rating
Symbol
Min
Typ
Max
OUTPUT SECTION
Output high short circuit pulsed current VDRV = 0 V, PW v 10 ms (Note 1)
IDRVsource
-
Output low short circuit pulsed current VDRV = Vcc, PW v 10 ms (Note 1)
IDRVsink
-
Output resistor (Typical value @ 25°C) Source
ROH
-
Output resistor (Typical value @ 25°C) Sink
ROL
-
High level output voltage, VBIAS-VDRV_XX @ IDRV_XX = 20 mA
VDRV_H
-
Low level output voltage VDRV_XX @ IDRV_XX = 20 mA
VDRV_L
-
DYNAMIC OUTPUT SECTION
250
-
500
-
30
60
10
20
0.7
1.6
0.2
0.6
Turn-on propagation delay (Vbridge = 0 V) (Note 2)
Turn-off propagation delay (Vbridge = 0 V or 50 V) (Note 3)
Shutdown propagation delay, when Shutdown is enabled
Shutdown propagation delay, when Shutdown is disabled
Output voltage rise time (from 10% to 90% @ VCC = 15 V) with 1 nF load
Output voltage fall time (from 90% to 10% @ VCC = 15 V) with 1 nF load
Propagation delay matching between the High side and the Low side
@ 25°C (Note 4)
tON
tOFF
tsd_en
tsd_dis
tr
tf
Dt
-
620
800
-
100
170
-
100
170
-
620
800
-
85
160
-
35
75
-
10
45
Internal fixed dead time (Note 5)
DT
400
520
650
INPUT SECTION
Low level input voltage threshold
Input pull-down resistor (VIN < 0.5 V)
High level input voltage threshold
Logic “1” input bias current @ VIN = 5 V @ 25°C
Logic “0” input bias current @ VIN = 0 V @ 25°C
SUPPLY SECTION
VIN
-
-
0.8
RIN
-
200
-
VIN
2.3
-
-
IIN+
-
5
25
IIN-
-
-
2.0
Vcc UV Start-up voltage threshold
Vcc_stup
8.0
8.9
9.8
Vcc UV Shut-down voltage threshold
Vcc_shtdwn
7.3
8.2
9.0
Hysteresis on Vcc
Vcc_hyst
0.3
0.7
-
Vboot Start-up voltage threshold reference to bridge pin
(Vboot_stup = Vboot - Vbridge)
Vboot_stup
8.0
8.9
9.8
Vboot UV Shut-down voltage threshold
Vboot_shtdwn 7.3
8.2
9.0
Hysteresis on Vboot
Vboot_shtdwn 0.3
0.7
-
Leakage current on high voltage pins to GND
(VBOOT = VBRIDGE = DRV_HI = 600 V)
IHV_LEAK
-
Consumption in active mode (Vcc = Vboot, fsw = 100 kHz and 1 nF load on
ICC1
-
both driver outputs)
5
40
4
5
Consumption in inhibition mode (Vcc = Vboot)
ICC2
-
250
400
Vcc current consumption in inhibition mode
ICC3
-
200
-
Vboot current consumption in inhibition mode
ICC4
1. Parameter guaranteed by design.
2. TON = TOFF + DT
3. Turn-off propagation delay @ Vbridge = 600 V is guaranteed by design.
4. See characterization curve for Dt parameters variation on the full range temperature.
5. Timing diagram definition see: Figure 4, Figure 5 and Figure 6.
-
50
-
Units
mA
mA
W
W
V
V
ns
ns
ns
ns
ns
ns
ns
ns
V
kW
V
mA
mA
V
V
V
V
V
V
mA
mA
mA
mA
mA
http://onsemi.com
4
Share Link: 