AD8180AR 查看數據表（PDF） - Analog Devices

零件编号

产品描述 (功能)

生产厂家

AD8180AR

750 MHz, 3.8 mA 10 ns Switching Multiplexers

Analog Devices 

AD8180/AD8182

APPLICATIONS

Multiplexing two RGB Video Sources

A common video application requires two RGB sources to be

multiplexed together before the selected signal is applied to a

monitor. Typically one source would be the PC’s normal output,

the second source might be a specialized source such as MPEG

video. Figure 23 shows how such a circuit could be realized

using the AD8180 and AD8182 and three current feedback op

amps. The video inputs to the multiplexers are terminated with

75 Ω resistors. This has the effect of halving the signal amplitude

of the applied signals.

Because all three multiplexers are permanently active, the

ENABLE pins are tied permanently low. The three SELECT

pins are tied together and this signal is used to select the source.

In order to drive a 75 Ω back terminated load (RL = 150 Ω), the

multiplexer outputs are buffered using the AD8001 current feed-

back op amp. A gain of two compensates for the signal halving by

the AD8001 output back termination resistor so that the system

has an overall gain of unity.

If lower speed and crosstalk can be tolerated, either of the triple

op amps, AD8013 or AD8073, can replace the three AD8001 op

amps in the above circuit. Because both devices have bandwidths

in the 100 MHz to 140 MHz range at a gain of +2, these ampli-

fiers will dominate the frequency response of the circuit.

With no signal present, the total quiescent current of the cir-

cuit in Figure 23 is 25.6 mA (3.8 mA + 6.8 mA + 3 × 5 mA), or

about 8.5 mA per channel. If either the AD8013 or AD8073

are used, the quiescent current will decrease to about 6.5 mA

per channel.

To reduce power consumption further, three AD8011 single

op amps can be used. With a quiescent current of 1 mA, this

will reduce the per channel quiescent current to about 4.5 mA.

Table II. Amplifier Options for RGB Multiplexer

Op Amp Comments

AD8001

AD8011

AD8013

AD8073

Highest Bandwidth, 440 MHz (G = +2), ISY = 5 mA

Lower Power Consumption, Bandwidth (G = +2) =

210 MHz, ISY = 1 mA

Triple Op Amp, Bandwidth (G = +2) = 140 MHz,

ISY = 3.4 mA

Lower Power Triple Op Amp, Bandwidth (G = +2) =

100 MHz, ISY = 3.5 mA

MPEG

R

G

B

75⍀

75⍀

+VS

75⍀

75⍀

75⍀ +VS

75⍀

R

G

B

COMPUTER

GRAPHICS

681⍀

681⍀

+VS 10␮F

0.1␮F

0.1␮F

+

10␮F

0.1␮F

+

10␮F

1 +1

2

DECODER

3 +1

4 AD8180

1 +1

2

DECODER

3 +1

4 AD8182

5 +1

6

DECODER

7 +1

8

ENABLE

7

6

5

–VS

0.1␮F

+

10␮F

14

ENABLE A

13

12

0.1␮F

11

+

10 10␮F

–VS

9

ENABLE B

8

AD8001

0.1␮F

10␮+F

681⍀

–VS

681⍀

+VS 10␮F

0.1␮F

681⍀

AD8001

0.1␮F

10␮F

+

–VS

681⍀

+VS 10␮F

0.1␮F

RTERM

AD8001

0.1␮F

SELECT

10␮+F

–VS

Figure 23. Multiplexing Two Component Video Sources

75⍀

R

75⍀

G MONITOR

B

75⍀

–8–

REV. B

Share Link: