PI5C3384 查看數據表（PDF） - Pericom Semiconductor
零件编号
产品描述 (功能)
生产厂家
PI5C3384 Datasheet PDF : 6 Pages
| |||
PI5C3384/3384C/32384 (25 Ohm)
10-Bit, 2-Port Bus switch 1122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................................................. –65°C to +150°C
Ambient Temperature with Power Applied ................................ –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) .......... –0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) ....... –0.5V to +7.0V
DC Input Voltage ......................................................................... –0.5V to +7.0V
DC Output Current ................................................................................... 120 mA
Power Dissipation ......................................................................................... 0.5W
Note:
Stresses greater than those listed under MAXI-
MUM RATINGS may cause permanent damage
to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions above those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect reli-
ability.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V ±5%)
Parameters Description
Test Conditions(1)
Min. Typ(2)
VIH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
—
VIL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5 —
IIH
Input HIGH Current
VCC = Max., VIN = VCC
—
—
IIL
Input LOW Current
VCC = Max., VIN = GND
—
—
IOZH
High-Impedance Output Current 0 ≤ A, B ≤ VCC
—
—
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18 mA —
–0.7 –1.2
IOS
Short Circuit Current(3)
A (B) = 0V, B (A) = VCC
100 —
VH
Input Hysteresis at Control Pins
— 150
RON
Switch On Resistance(4)
VCC = Min., VIN = 0.0V,
ION = 48 mA
PI5C3384
PI5C3384C
PI5C32384
—
5
—
5
20
28
VCC = Min., VIN = 2.4V,
ION = 15 mA
PI5C3384
PI5C3384C
PI5C32384
—
10
—
10
20
35
Max.
—
0.8
±1
±1
±1
V
—
—
7
7
40
15
15
48
Units
V
V
µA
µA
µA
mA
mV
ohm
ohm
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(5)
Description
CIN
Input Capacitance
COFF
A/B Capacitance, Switch Off
CON
A/B Capacitance, Switch On
Test Conditions
VIN = 0V
VIN = 0V
VIN = 0V
Typ
Max. Units
—
6
pF
—
6
pF
—
8
pF
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, TA = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the
lower of the voltages on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
2
PS 7029B
11/18/02
Share Link: 