RE46C121 查看數據表（PDF） - R and E International, Inc.

零件编号

产品描述 (功能)

生产厂家

RE46C121

CMOS Ionization Smoke Detector ASIC with Interconnect

R and E International, Inc. 

RE46C121

CMOS Ionization Smoke Detector ASIC with Interconnect

Product Specification

R&E International

DEVICE DESCRIPTION and APPLICATION NOTES

Note: All timing references are nominal values. Refer to the electrical specifications for limits

Internal Timing – With external components as indicated on the application drawing the period of the

oscillator is nominally 1.67 seconds in standby. Every 1.66 seconds the detection circuitry is powered up

for 10.5mS and the status of the smoke comparator is latched. In addition every 40 seconds the LED

driver is turned on for 10.5mS and the status of the low battery comparator is latched. The smoke

comparator status is not checked during the low battery test, during the low battery horn warning chirp, or

when the horn is on due to an alarm condition.

If an alarm condition is detected the oscillator period increases to 41.5mS.

Due to the low currents used in the oscillator the capacitor on pin 12 should be a low leakage type.

Oscillator accuracy will depend mainly on the tolerance of the RBIAS resistor and OSCAP capacitor.

Smoke Detection Circuit – The smoke comparator compares the ionization chamber voltage to a voltage

derived from a resistor divider across VDD. This divider voltage is available externally on pin 13 (VSEN).

Pin 13 (VSEN) can be used to modify the internal set point for the smoke comparator by using external

resistors to VDD or VSS. Nominal values for the internal resistor divider are indicated on the block

diagram. These internal resistor values can vary by up to ±20% but the resistor matching will be <2% on

any one device. A transmission switch on pin 13 isolates this pin during the low battery test so that the

low battery set point will not be affected if external resistors are used to modify the smoke sensitivity set

point.

The guard amplifier and outputs are always active and will be within 50mV of the DETECT input to

reduce surface leakage. The guard outputs also allow for measurement of the DETECT input without

loading the ionization chamber.

Low Battery Detection - An internal reference is compared to the voltage divided VDD supply. The battery

can be checked under load via the LED low side driver output since low battery status is latched at the

end of the 11mS LED pulse. Pin 3 (LBADJ) can be used to modify the low battery set point by placing a

resistor to VDD or VSS. Note that the internal resistor string is common to both pin 3 and pin 13 so there

will be some interaction between the two. Modification of the low battery set point may affect the smoke

sensitivity setting.

LED Pulse – The LED is pulsed on for 10.5mS every 40S in standby. In alarm the LED is pulsed on for

10.5mS every 1S. For a remote alarm condition the LED is always off.

Interconnect – Pin 2 (IO) provides the capability to common many detectors in a single system. If a single

unit goes into alarm the IO pin is driven high. This high signal causes the interconnected units to alarm.

The LED flashes every 1S for 10.5mS on the signaling unit and is inhibited on the units that are in alarm

due to the IO signal. An internal sink device on the IO pin helps to discharge the interconnect line. This

dump device is active for 1 clock cycle after the unit exits the alarm condition (1.67S).

The interconnect input has a 500mS nominal digital filter. This allows for interconnection to other types of

alarms (carbon monoxide for example) that may have a pulsed interconnect signal.

Testing - By holding pin 12 (OSCAP) low the internal power strobe is active and pin1 (DETCOMP) can be

used to check for smoke. Please refer to the timing diagrams.

Telephone 610.992.0727

Facsimile 610.992.0734

E-mail: rande@randeint.com

Page 5 of 8

DS-RE46C121-010907

This datasheet contains PROPRIETARY and CONFIDENTIAL information.

Share Link: