SAA7128AH 查看數據表（PDF） - Philips Electronics

零件编号

产品描述 (功能)

生产厂家

SAA7128AH

Digital video encoder

Philips Electronics 

Philips Semiconductors

Digital video encoder

Product specification

SAA7128AH; SAA7129AH

7 FUNCTIONAL DESCRIPTION

The digital video encoder encodes digital luminance and

colour difference signals into analog CVBS, S-video and

simultaneously RGB or CR-Y-CB signals. NTSC-M,

PAL-B/G, SECAM and sub-standards are supported.

Both interlaced and non-interlaced operation is possible

for all standards.

The basic encoder function consists of subcarrier

generation, colour modulation and insertion of

synchronization signals. Luminance and chrominance

signals are filtered in accordance with the standard

requirements of “RS-170-A” and “ITU-R BT.470-3”.

For ease of analog post filtering, the signals are twice

oversampled with respect to the pixel clock before

digital-to-analog conversion.

The total filter transfer characteristics are illustrated in

Figs 8 to 13. The DACs for Y, C and CVBS are realized

with full 10-bit resolution; 9-bit resolution for RGB output.

The CR-Y-CB to RGB dematrix can be bypassed optionally

in order to provide the upsampled CR-Y-CB input signals.

The 8-bit multiplexed CB-Y-CR formats are “ITU-R BT.656”

(D1 format) compatible, but the SAV and EAV codes can

be decoded optionally, when the device is operated in

slave mode. Two independent data streams can be

processed, one latched by the rising edge of LLC1, the

other latched by the falling edge of LLC1. The purpose of

that is e.g. to forward one of the data streams containing

both video and On-Screen Display (OSD) information to

the RGB outputs, and the other stream containing video

only to the encoded outputs CVBS and S-video.

For optimum display of RGB signals through a

euro-connector TV set, an early composite sync pulse

(up to 31 LLC1 clock periods) can be provided on the

CVBS output.

As a further alternative, the VBS and C outputs may

provide a second and third CVBS signal.

It is also possible to connect a Philips digital video decoder

of the SAA711x family to the SAA7128AH; SAA7129AH.

Via the RTCI pin, connected to RTCO of a decoder,

information concerning actual subcarrier, PAL-ID and

definite subcarrier phase can be inserted.

The device synthesizes all necessary internal signals,

colour subcarrier frequency and synchronization signals

from that clock.

Wide screen signalling data can be loaded via the I2C-bus

and is inserted into line 23 for standards using 50 Hz field

rate.

VPS data for program dependent automatic start and stop

of such featured VCR’s is loadable via I2C-bus.

The IC also contains closed caption and extended data

services encoding (line 21), and supports anti-taping

signal generation in accordance with Macrovision. It is also

possible to load data for copy generation management

system into line 20 of every field (525/60 line counting).

A number of possibilities are provided for setting different

video parameters, such as:

• Black and blanking level control

• Colour subcarrier frequency

• Variable burst amplitude, etc.

During reset (RESET = LOW) and after reset is released,

all digital I/O stages are set to input mode and the encoder

is set to PAL mode and outputs a ‘black burst’ signal on

CVBS and S-video outputs, while RGB outputs are set to

their lowest output voltages. A reset forces the I2C-bus

interface to abort any running bus transfer.

7.1 Versatile fader

Important note: whenever the fader is activated with the

SYMP bit set to a logic 1 (enabling the detection of

embedded Start of Active Video (SAV) and End of Active

Video (EAV)), codes 00H and FFH are not allowed within

the actual video data (as prescribed by “ITU-R BT.656”,

anyway). If SAV (00H) has been detected, the fader

automatically passes 100% of the respective signal until

SAV will be detected.

Within the digital video encoder, two data streams can be

faded against each other; these data streams can be input

to the double speed MPEG port, which is able to separate

two independent 27 MHz data streams MPA and MPB via

a cross switch controlled by EDGE1 and EDGE2.

handbook, halfpage

MPpos

MPneg

EDGE1 = 0

EDGE1 = 1

EDGE2

=

EDGE2

1

=

0

MPA

MPB

MHB574

Fig.3 Cross switch.

2003 Dec 09

8

Share Link: