TC7652
1.0 ELECTRICAL
CHARACTERISTICS
ABSOLUTE MAXIMUM RATINGS*
Total Supply Voltage (VDD to VSS) .......................+18V
Input Voltage .................... (VDD +0.3V) to (VSS – 0.3V)
Voltage on Oscillator Control Pins...............VDD to VSS
Duration of Output Short Circuit ..................... Indefinite
Current Into Any Pin............................................ 10mA
While Operating (Note 1)............................ 100µA
Package Power Dissipation (TA < 70°C)
8-Pin Plastic DIP ....................................... 730mW
14-Pin Plastic DIP ..................................... 800mW
Storage Temperature Range .............. -65°C to +150°C
Operating Temperature Range
C Device .......................................... 0°C to +70°C
I Device ......................................... -25°C to +85°C
TC7652 ELECTRICAL SPECIFICATIONS
*Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
These are stress ratings only and functional operation of the
device at these or any other conditions above those indi-
cated in the operation sections of the specifications is not
implied. Exposure to Absolute Maximum Rating conditions
for extended periods my affect device reliability.
Electrical Characteristics: VDD = +5V, VSS = -5V, TA = +25°C, unless otherwise indicated.
Symbol
Parameter
Min
Typ
Max
Units
Test Conditions
VOS
TCVOS
VOS/DT
IBIAS
IBIAS
IOS
RIN
OL
VOUT
CMVR
Input Offset Voltage
—
Average Temperature Co-efficient of
—
Input Offset Voltage
Offset Voltage vs Time
—
Input Bias Current (CLK On)
—
—
—
Input Bias Current (CLK Off)
—
—
—
Input Offset Current
—
Input Resistance
—
Large Signal Voltage Gain
120
Output Voltage Swing (Note 2)
±4.7
—
Common Mode Voltage Range
-4.3
±2
0.01
150
30
100
250
15
35
100
25
1012
150
±4.85
±4.95
—
±5
0.05
—
100
—
1000
30
—
1000
150
—
—
—
—
+3.5
µV TA = +25°C
µV/°C 0°C < TA < +70°C
nV/mo
pA TA = +25°C
0°C < TA < +70°C
-25°C < TA < +85°C
pA TA = +25°C
0°C < TA < +70°C
-25°C < TA < +85°C
pA
Ω
dB RL = 10kΩ, VOUT = ±4V
V RL = 10kΩ
RL = 100kΩ
V
MRR
Common Mode Rejection Ratio
120
140
—
dB CMVR = -4.3V to +3.5V
PSRR
eN
IN
Power Supply
Input Noise Voltage
Input Noise Current
120
140
—
dB ±3V to ±8V
—
0.2
1.5
µVP-P RS = 100Ω, DC to 1Hz
—
0.7
5
µVP-P DC to 10Hz
—
0.01
—
pA/ f = 10Hz
√Hz
GBW
Unity Gain Bandwidth
—
0.4
—
MHz
SR
Slew Rate
Overshoot
—
1
—
V/µsec CL = 50pF, RL = 10kΩ
—
15
—
%
VDD, VSS
Note 1:
2:
3:
Operating Supply Range
5
—
16
V
Limiting input current to 100µA is recommended to avoid latch-up problems. Typically 1mA is safe however, this is not
guaranteed.
Output clamp not connected. See typical characteristics curves for output swing versus clamp current characteristics.
See “Output Clamp” under detailed description.
© 2002 Microchip Technology Inc.
DS21464B-page 3