TC7650(2002) 查看數據表（PDF） - Microchip Technology

零件编号

产品描述 (功能)

生产厂家

TC7650
(Rev.:2002)

Chopper Stabilized Operational Amplifie

Microchip Technology 

TC7650

2.0 PIN DESCRIPTIONS

The descriptions of the pins are listed in Table 2-1.

TABLE 2-1: PIN FUNCTION TABLE

Pin Number

8-pin DIP 14-pin DIP

Symbol

Description

1,8

2,1

CA, CB

Nulling capacitor pins

2

4

-INPUT Inverting Input

3

5

+INPUT Non-inverting Input

4

7

VSS

Negative Power Supply

5

9

OUTPUT Output Voltage Clamp

CLAMP

6

10

OUTPUT Output

7

11

—

3,6

VDD

Positive Power Supply

NC

No internal connection

—

8

CRETN

Capacitor current return pin

—

12

INT CLK OUT Internal Clock Output

—

13

EXT CLK IN External Clock Input

—

14

INT/EXT Select Internal or External Clock

3.0 DETAILED DESCRIPTION

3.1 Theory of Operation

Figure 3-1 shows the major elements of the TC7650.

There are two amplifiers (the main amplifier and the

nulling amplifier), and both have offset null capability.

The main amplifier is connected full-time from the input

to the output. The nulling amplifier, under the control of

the chopping frequency oscillator and clock circuit,

alternately nulls itself and the main amplifier. Two exter-

nal capacitors provide the required storage of the null-

ing potentials and the necessary nulling loop time

constants. The nulling arrangement operates over the

full common mode and power supply ranges, and is

also independent of the output level, thus giving excep-

tionally high CMRR, PSRR and AVOL.

Careful balancing of the input switches minimizes

chopper frequency charge injection at the input termi-

nals, and the feed forward type injection into the com-

pensation capacitor that can cause output spikes in this

type of circuit.

The circuit's offset voltage compensation is easily

shown. With the nulling inputs shorted, a voltage

almost identical to the nulling amplifier offset voltage is

stored on CA. The effective offset voltage at the null

amplifier input is:

EQUATION 3-1:

VOSE

=

--------1---------

AN + 1

VO

S

N

After the nulling amplifier is zeroed, the main amplifier

is zeroed; the A switches open and B switches close.

The output voltage equation is:

EQUATION 3-2:

VOUT = AM[VOSM + (V+ - V-) + AN(V+ - V-) + AN VOSE]

EQUATION 3-3:

VOUT = AMAN (V+ – V-) + -V----O-----S-----M---A---+--N---V----O-----S-----N--

As desired, the device offset voltages are reduced by

the high open loop gain of the nulling amplifier.

3.2 Output Stage/Loading

The output circuit is a high impedance stage (approxi-

mately 18kΩ). With loads less than this, the chopper

amplifier behaves in some ways like a trans-conduc-

tance amplifier whose open-loop gain is proportional to

load resistance. For example, the open loop gain will

be 17dB lower with a 1kΩ load than with a 10kΩ load.

If the amplifier is used strictly for DC, the lower gain is

of little consequence, since the DC gain is typically

greater than 120dB, even with a 1kΩ load. In wideband

applications, the best frequency response will be

achieved with a load resistor of 10kΩ or higher. This

results in a smooth 6dB/octave response from 0.1Hz to

2MHz, with phase shifts of less than 10° in the transi-

DS21463B-page 4

© 2002 Microchip Technology Inc.

Share Link: