SDN10-24-100P 查看數據表（PDF） - Unspecified

零件编号

产品描述 (功能)

生产厂家

SDN10-24-100P

Power Supplies

Unspecified 

Power Supplies

SDN-P Specifications (Single Phase), 12 Vdc and 48 Vdc Output

Description

Catalog Number

SDN 9-12-100P

SDN 5-48-100P

SDN 16-12-100P

Input

Nominal Voltage

115/230 Vac auto select

-AC Range

85-132/176-264 Vac; 210 - 375 Vdc

-DC Range 1

210 - 375 Vdc

-Frequency

47 - 63 Hz

Nominal Current 2

2.0 A / 1.5 A

4 A / 2.3 A

3.3 A / 1.7 A

-Inrush current max.

Typ. < 20 A

typ. < 40 A

Efficiency (Losses 3)

> 84% typ. (17.28 W)

> 88% typ. (28.8 W)

> 84% typ. (30.72 W)

Power Factor Correction

Units fulfill EN61000-3-2

Output

Nominal Voltage

12 V (11.6-15.2 Vdc Adj.)

48 V (35.8 - 52 Vdc Adj.)

12 V (11.6-14.2 Vdc Adj.)

Tolerance

< ±2 % overall (combination Line, load, time and temperature related changes)

-Line Regulation

< 0.5%

-Load Regulation

< 0.5%

-Time & Temp. Drift

< 1%

Ripple 4

< 50 mVpp

Overvoltage Protection

< 16 Vdc with auto-recovery

< 60 Vdc with auto-recovery

< 16 Vdc with auto-recovery

Nominal Current

9 A (108 W)

5 A (240 W)

16 A (192 W)

-Current Limit

110% of nominal - Fold Forward (Current rises, voltage drops to maintain constant power during overload up to max peak current)

Holdup Time 5

>20 ms @ full load

Parallel Operation

Supplies will not be damaged with parallel operation

Power Back Immunity

16 Vdc

60 Vdc

16 Vdc

General

EMC: -Emissions

EN61000-6-3, EN61204-3, EN55022 Class B, EN61000-3-2, EN61000-3-3

-Immunity

Temperature

EN61000-6-2, EN61204-3, EN55024, IEC61000-4-2, IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-6, IEC61000-4-8, IEC61000-4-11

Storage: -25 to +85oC, Operation -10 to +60oC full power; with linear derating to half power from 60 to 70oC

(Convection cooling, no forced air required). Operation up to 50% load permissible with sideways or front side up mounting orientation.

Humidity

< 90% RH, non-condensing; IEC 68-2-2, 68-2-3

MTBF:

- Standard

>500,000 hrs

Telcordia/Bellcore, Issue Case 3 @ 25oC

Warranty

General Protection/Safety

5 year limited warranty

Protected against continuous short -circuit, continuous overload, continuous open circuit. Protection Class 1 (IEC536),

Degree of Protection IP20 (IEC 529) Safe low voltage: SELV (acc. EN60950)

Status Indicators (Visual)

Status Indicators (Relay)

Green LED on when Vout > 75% (with ± 5% tolerance) of nominal output voltage

Normally Open solid state relay - signal active when Vout >70% of nominal output voltage (rated up to 200 mA, 60 Vdc)

Installation

Fusing

-Input

-Output

Mounting

Internally fused

Outputs are capable of providing high currents for short periods of time for inductive load startup or switching. Fusing may be required if

Nominal O/P current rating cannot be tolerated. Continuous current overload allows for reliable fuse tripping.

Simple snap-on to DIN TS35/7.5 or TS35/15 rail system. Unit should handle normal shock and vibration of industrial use

and transportation without falling off the rail.

Connections

Input: Screw terminals, connector size range: 16-10 AWG (1.5-6mm2) for solid conductors.

Output: Two terminals per output, connector size range: 16-10 AWG (1.5-6mm2) for solid conductors.

Case

Fully enclosed metal housing with fine ventilation grid to keep out small parts.

-Free Space

70 mm above and below, 25 mm left and right, 15mm in front

H x W x D inches (mm)

4.88 × 2.56 × 4.55 (124.0 x 65.0 × 116.0)

4.88 × 3.23 × 4.55 (124.0 × 83.0 × 116.0)

Weight lbs (kg)

2.4 (1.10)

3.3 (1.50)

1. Not UL listed for DC input.

2. Input current ratings are conservatively specified with low input, worst case

efficiency and power factor.

3. Losses are heat dissipation in watts at full load, nominal input line.

4. Ripple/noise is stated as typical values when measured with a 20 MHz,

bandwidth scope and 50 Ohm resistor.

5. Full load, 100 Vac Input @ Tamb = +25°C

134

Visit our website at www.emerson.com or contact Technical Services at (800) 377-4384 with any questions.

© January 2017

Share Link: