LTC1164-5C 查看數據表（PDF） - Linear Technology
零件编号
产品描述 (功能)
生产厂家
LTC1164-5C Datasheet PDF : 16 Pages
| |||
LTC1164-5
APPLICATIO S I FOR ATIO
Any parasitic switching transients during the rise and fall
edges of the incoming clock are not part of the clock
feedthrough specifications. Switching transients have fre-
quency contents much higher than the applied clock; their
amplitude strongly depends on scope probing techniques
as well as grounding and power supply bypassing. The
clock feedthrough, if bothersome, can be greatly reduced
by adding a simple R/C lowpass network at the output of
the filter pin (Pin 9). This R/C will completely eliminate any
switching transient.
Wideband Noise
The wideband noise of the filter is the total RMS value of
the device’s noise spectral density and it is used to
determine the operating signal-to-noise ratio. Most of its
frequency contents lie within the filter passband and it
cannot be reduced with post filtering. For instance, the
LTC1164-5 wideband noise at ±2.5V supply is 100µVRMS,
95µVRMS of which have frequency contents from DC up to
the filter’s cutoff frequency. The total wideband noise
(µRMS) is nearly independent of the value of the clock. The
clock feedthrough specifications are not part of the wide-
band noise.
Speed Limitations
The LTC1164-5 optimizes AC performance versus power
consumption. To avoid op amp slew rate limiting at
maximum clock frequencies, the signal amplitude should
be kept below a specified level as shown in Table 3.
Table 3. Maximum VIN vs VS and fCLK
POWER SUPPLY
MAXIMUM fCLK
VS = ±7.5V
1.5MHz
VS = ±7.5V
1.0MHz
VS = ±5.0V
1.0MHz
Single 5V
1.0MHz
MAXIMUM VIN
1VRMS (fIN > 35kHz)
0.5VRMS (fIN > 250kHz)
3VRMS (fIN > 25kHz)
0.7VRMS (fIN > 250kHz)
2.5VRMS (fIN > 25kHz)
0.5VRMS (fIN > 100kHz)
0.7VRMS (fIN > 25kHz)
0.5VRMS (fIN > 100kHz)
Aliasing
Aliasing is an inherent phenomenon of sampled data
systems and it occurs when input frequencies close to the
sampling frequency are applied. For the LTC1164-5 case
at 100:1, an input signal whose frequency is in the range
of fCLK ±2.5% will be aliased back into the filter’s pass-
band. If, for instance, an LTC1164-5 operating with a
100kHz clock and 1kHz cutoff frequency receives a 98kHz
10mV input signal, a 2kHz 56µV alias signal will appear at
its output. When the LTC1164-5 operates with a clock-to-
cutoff frequency of 50:1, aliasing occurs at twice the clock
frequency. Table 4 shows details.
Table 4. Aliasing Data (fCLK = 100kHz, VS = ±5V)
INPUT FREQUENCY
OUTPUT LEVEL
OUTPUT FREQUENCY
(VIN = 1VRMS)
(Relative to Input)
(Aliased Frequency)
(fCLK/fC) = 100:1, fCUTOFF = 1kHz
97.0kHz
–102.0dB
3.0kHz
97.5kHz
– 65.0dB
2.5kHz
98.0kHz
– 45.0dB
2.0kHz
98.5kHz
– 23.0dB
1.5kHz
99.0kHz
– 4.0dB
1.0kHz
99.5kHz
– 0.3dB
0.5kHz
(fCLK/fC) = 50:1, fCUTOFF = 2kHz
197.0kHz
197.5kHz
198.0kHz
– 23.0dB
–12.0dB
– 5.0dB
198.5kHz
199.0kHz
–1.8dB
–1.0dB
199.5kHz
– 0.8dB
3.0kHz
2.5kHz
2.0kHz
1.5kHz
1.0kHz
0.5kHz
Table 5. Transient Response of LTC Lowpass Filters
LOWPASS FILTER
DELAY
TIME*
(SEC)
RISE SETTLING
TIME** TIME***
(SEC) (SEC)
LTC1064-3 Bessel
LTC1164-5 Bessel
LTC1164-6 Bessel
0.50/fC
0.43/fC
0.43/fC
0.34/fC
0.34/fC
0.34/fC
0.80/fC
0.85/fC
1.15/fC
LTC1264-7 Linear Phase
LTC1164-7 Linear Phase
LTC1064-7 Linear Phase
1.15/fC
1.20/fC
1.20/fC
0.36/fC
0.39/fC
0.39/fC
2.05/fC
2.20/fC
2.20/fC
LTC1164-5 Butterworth
LTC1164-6 Elliptic
0.80/fC
0.85/fC
0.48/fC
0.54/fC
2.40/fC
4.30/fC
LTC1064-4 Elliptic
LTC1064-1 Elliptic
0.90/fC
0.85/fC
0.54/fC
0.54/fC
4.50/fC
6.50/fC
* To 50% ±5%, ** 10% to 90% ±5%, *** To 1% ±0.5%
OVER-
SHOOT
(%)
0.5
0
1
5
5
5
11
18
20
20
11645fc
10
Share Link: 