MF0032M-04AAXX 查看數據表（PDF） - Mitsumi
零件编号
产品描述 (功能)
生产厂家
MF0032M-04AAXX Datasheet PDF : 32 Pages
| |||
MITSUBISHI STORAGE CARD
Preliminary
CompactFlash CARDS
Configuration Register Specifications
Configuration Option Register
This register is used for the configuration of the card
configuration status and for the issuing soft reset to the card.
D7
D6
D5 D4 D3 D2 D1 D0
SRESET LevIREQ
Index
Name R/W
Description
SRESET R/W Setting this bit to “1”, places the card in the reset
state. When the host returns this bit to “0”, the
function shall enter the same unconfigured, reset
state as the card does following a power-up and
hardware reset.
LevIREQ R/W If this bit is set to “0”, card generates pulse mode
interrupt. If this bit is set to “1”, card generates
level mode interrupts.
Index
R/W This bits is used for select operation mode of the
card as follows.
When Power on, Card Hard Reset and Soft reset,
this data is “000000” for the purpose of Memory
card interface recognition.
Index: 0 -> Memory mapped
1 -> Contiguous I/O mapped
2 -> Primary I/O mapped
3 -> Secondary I/O mapped
Configuration and Status Register
This register is used for observing the card state.
D7
D6
D5 D4 D3
D2
D1 D0
Changed SigChg Iois8 0
0 PwrDwn Intr 0
Name
Changed
SigChg
Iois8
PwrDwn
Intr
R/W
Description
R/O This bit indicates that CREADY bit on the Pin
Replacement register is set to “1”. When
Changed bit is set to “1”, STSCHG# pin is held
“L” if the SigChg bit is “1” and the card is
configured for the I/O interface.
R/W This bit is set or reset by the host for enabling
and disabling the status change
signal(STSCHG# pin). When the card is
configured I/O card interface and this bit is set to
“1”, STSCHG# pin is controlled by Changed bit.
If this bit is set to “0”, STSCHG# pin is kept “H”.
R/W This card is always configured for both 8-bit and
16-bit I/O, so this bit is ignored.
R/W When this bit is set to “1”, the card enters Power
Down mode. When this bit is reset to “0”, the
host is requesting the card to enter the active
mode. RREADY bit on Pin Replacement
Register becomes BUSY when this bit is
changed. RREADY will not become Ready until
the power state requested has been entered.
This card automatically powers down when it is
idle, and powers back up when it receives a
command.
R/W This bit represents the internal state of the
interrupt request. This bit state is available
whether I/O card interface has been configured
or not. This signal remains True until the
condition which caused the interrupt request has
been serviced. If interrupts are disabled by the
nIEN bit in the Device Control Register, this bit is
a zero.
Pin Replacement Register
This register is used for providing the signal state of READY
signal when the card configured I/O card interface.
D7 D6
D5
D4 D3 D2
D1
D0
0
0 CREADY 0
1
1 RREADY 0
Name
CREADY
RREADY
R/W
Description
R/W This bit is set to “1” when the RREADY bit
changes state. This bit may also be written by
the host.
R/W When read, this bit indicates READY pin states.
When written, this bit acts as a mask for writing
the CREADY bit.
Socket and Copy Register
This register is used for identification of the card from the other
cards. Host can read and write this register. This register should
be set by host before this card’s Configuration Option register
set.
D7
D6
D5
D4
D3
D2
D1
D0
0
Copy Number
Socket Number
Name
R/W
Description
Copy Number R/W This bit indicates the drive number of the
card for twin card configuration.
And the host can select and drive one card
by comparing the number in this field with
the drive number of Drive Head Register.
In the way, the host can perform the card’s
master/slave organization.
Socket Number R/W This field indicates to the card that it is
located in the n’th socket.
MITSUBISHI
ELECTRIC
10
Oct.1999. Rev. 0.2
Share Link: 