LT1228(Rev_A) 查看數據表（PDF） - Linear Technology
零件编号
产品描述 (功能)
生产厂家
LT1228 Datasheet PDF : 20 Pages
| |||
FEATURES
s Very Fast Transconductance Amplifier
Bandwidth: 75MHz
gm = 10 × ISET
Low THD: 0.2% at 30mVRMS Input
Wide ISET Range: 1µA to 1mA
s Very Fast Current Feedback Amplifier
Bandwidth: 100MHz
Slew Rate: 1000V/µs
Output Drive Current: 30mA
Differential Gain: 0.04%
Differential Phase: 0.1°
High Input Impedance: 25MΩ, 6pF
s Wide Supply Range: ±2V to ±15V
s Inputs Common Mode to Within 1.5V of Supplies
s Outputs Swing Within 0.8V of Supplies
s Supply Current: 7mA
APPLICATI S
s Video DC Restore (Clamp) Circuits
s Video Differential Input Amplifiers
s Video Keyer/Fader Amplifiers
s AGC Amplifiers
s Tunable Filters
s Oscillators
LT1228
100MHz Current Feedback
Amplifier with DC Gain Control
DESCRIPTIO
The LT1228 makes it easy to electronically control the gain
of signals from DC to video frequencies. The LT1228
implements gain control with a transconductance amplifier
(voltage to current) whose gain is proportional to an exter-
nally controlled current. A resistor is typically used to
convert the output current to a voltage, which is then
amplified with a current feedback amplifier. The LT1228
combines both amplifiers into an 8-pin package, and oper-
ates on any supply voltage from 4V (±2V) to 30V (±15V). A
complete differential input, gain controlled amplifier can be
implemented with the LT1228 and just a few resistors.
The LT1228 transconductance amplifier has a high imped-
ance differential input and a current source output with wide
output voltage compliance. The transconductance, gm, is
set by the current that flows into pin 5, ISET. The small signal
gm is equal to ten times the value of ISET and this relationship
holds over several decades of set current. The voltage at pin
5 is two diode drops above the negative supply, pin 4.
The LT1228 current feedback amplifier has very high input
impedance and therefore it is an excellent buffer for the
output of the transconductance amplifier. The current feed-
back amplifier maintains its wide bandwidth over a wide
range of voltage gains making it easy to interface the
transconductance amplifier output to other circuitry. The
current feedback amplifier is designed to drive low imped-
ance loads, such as cables, with excellent linearity at high
frequencies.
TYPICAL APPLICATI
Differential Input Variable Gain Amp
R3A
10k
+
VIN R2A
10k
–
R3
100Ω
15V
4.7µF
3+ 7
gm
2–
5
4
–15V
R2
100Ω
+
4.7µF
R4
1.24k
R6
6.19Ω
1+
6
CFA
VOUT
ISET
8–
RF
R5
470Ω
10k
R1
RG HIGH INPUT RESISTANCE
270Ω 10Ω EVEN WHEN POWER IS OFF
–18dB < GAIN < 2dB
VIN ≤ 3VRMS
LT1228 • TA01
Frequency Response
6
3
0
ISET = 1mA
VS = ±15V
RL = 100Ω
–3
–6
–9
–12
ISET = 300µA
–15
–18
ISET = 100µA
–21
–24
100k
1M
10M
100M
FREQUENCY (Hz)
LT1228 • TA02
1
Share Link: 